Paslode IM250 F-16 II Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Paslode IM250 F-16 II Скачать руководство пользователя страница 5

4

Safety Instructions

The following safety instructions have been included in this
booklet to provide you with basic information necessary for
safe operation of the Paslode Cordless

Finish nailer. DO

NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU
HAVE READ AND UNDERSTAND ALL SAFETY
PRECAUTIONS AND MANUAL INSTRUCTIONS.

In addition to these instructions, training may be necessary.
Contact your Paslode representative for additional
information.

DANGER

The Cordless

Finish nailer

is an internal combustion
device. It produces hot
exhaust gases that may
ignite flammable
materials. This tool must
not be used in a
combustible environment
or in the presence of
combustible materials,
such as flammable
chemicals, adhesives,
gasoline, or solvents.

WARNING

Do not attempt to operate
this tool until you have
read and understood all
safety precautions and
manual instructions.

Failure to follow all safety
precautions and
instructions may result in
a permanent loss of vision,
serious personal or even
fatal injury, property
damage and/or tool
damage.

WARNING

Do not expose the tool to
temperatures in excess of
120

°

F (49

°

C). Fuel and/

or the battery may burst,
releasing flammable gas.

WARNING

ALWAYS keep the
Paslode Cordless Finish
nailer, fuel cell, battery and
battery charger out of the
reach of children.

WARNING

This tool must be operated
only in a well-ventilated
environment, because
the tool exhausts carbon
monoxide similar to a gas
chainsaw or lawnmower.
Exposure to carbon
monoxide may cause
dizziness, nausea, or
unconsciousness.

«
...
3
4
5
6
7
...
»

Содержание IM250 F-16 II





















Отзывы:

Нет отзывов