![background image](http://html1.mh-extra.com/html/paslode/905600/905600_operating-manual_761488008.webp)
8
Battery And Charging System
Charging Instructions:
1.
2.
NOTE
3.
After charging, the red light will go out and the green
light will come on, indicating that the battery is fully
charged. The charger will keep the battery at full
charge until it is removed.
4.
Charging Times:
First charge (new battery)
1.5 hours
Discharged Battery
5 minutes to 1.5 hours
Charging Don'ts:
1.
Never charge battery outdoors or in temperatures
below 40 F (5 C).
2.
Never allow metal objects to come in contact with
battery terminals.
3.
Never puncture or attempt to open battery case or
cells.
4.
Never store battery where it will be subjected to
temperatures above 120 F (49 C).
5.
Never incinerate battery.
6.
Never use a defective battery charger, one that
overheats and/or smokes when plugged in.
7.
Never immerse the battery or charger in water.
Battery disposal:
The Paslode batteries contain lithium and should be re-
cycled or disposed of properly.
You may contact your local recycling center for information
on where to return the spent battery or call 1-800-822-8837
for information on Li-ion battery recycling in your area.
WARNING
CHEMICAL/EXPLOSION
HAZARD
Read ALL instructions before
charging or using battery.
Failure
to
follow
ALL
instructions may result in fire,
severe burns, or release of
toxic materials.
Important Charging Notes:
The Paslode Cordless
tool
comes with a rechargeable
Lithium Ion (Li-ion) battery and its own charging system.
This charging system is the only one that will work with
Paslode Li-ion batteries. The first step in preparing a new
tool for operation is to fully charge the battery. New batter-
ies are shipped partially discharged and must be
charged prior to first use. Batteries will take 5 minutes to
1.5 hour (time will be dependant on the amount of discharge
within the battery) to recharge.
Remove the battery from tool or case and insert termi-
nals down into charger. The red light will come on
indicating that the battery is charging and the green light
will go out.
If battery is completely discharged the red light and
the green light may flash back and forth for up to 20
minutes. This safety feature slowly recharges the
battery until it is ready to accept the full charging
current. If the red and green lights continue to flash
after 20 minutes, replace the battery.
Unplug the charger from the 120V AC or 240V AC
outlet.
Remove the
charger unit from the tool case and plug
it into a 120V AC outlet. Set the charger base on a
stable surface. A green light will come on to indicate
the power is on and the charger circuit is ready.
PASLODE 240V 50HZ BATTERY CHARGING SYSTEM
AC-DC Adapter
Charger Base
DC Plug
Battery
Plug Receptacle
6ft. Cord
Battery
Charger
TECHNICAL DATA
Impulse Adapter (AC-DC)
Australia/New Zealand
Impulse Charger Base
Battery
7.4 VDC, 2150mAh, Lithium-ion
t
u
p
n
I
240V, 50HZ
12VDC
Output
Polarity
12VDC, 1.8A
PASLODE 120V 60HZ BATTERY CHARGING SYSTEM
Charger Input
Battery
7.4 VDC, 2150mAh, Lithium-ion
120V AC, 60HZ
Output
Polarity
12VDC, 1.8A
1B.
Remove the wall transformer from the tool case and
plug into a 240V AC outlet. Set the charger base on a
stable surface and insert the wall transformer
unitʼs
plus
into the plug receptacle on the base of the charger (see
diagram). A green light indicates power is on and charg-
ing system is ready.
Australia/New Zealand
North America
North America
Australia/New Zealand