![background image](http://html1.mh-extra.com/html/paslode/515500/515500_operating-manual-and-tool-schematic_761481004.webp)
4
WARNING
Failure to follow any of the above instructions could result in severe personal
injury to tool user and bystanders or cause damage to tool and property.
Contact your local Paslode Representative for pr
ʼ
SAFETY INSTRUCTIONS
SAFETY FIRST
These safety instructions provide information necessary
for safe operation of Paslode
®
tools. DO NOT ATTEMPT
TO OPERATE THE TOOL UNTIL YOU READ AND
UNDERSTAND ALL SAFETY PRECAUTIONS AND
MANUAL INSTRUCTIONS.
WEAR EYE AND HEARING PROTECTION
are responsible for enforcing the use of eye protection.
THE TOOL MUST BE USED ONLY FOR THE PUR-
POSE FOR WHICH IT WAS DESIGNED
any way or use the tool as a hammer to knock material
into place.
NEVER ENGAGE IN HORSEPLAY WITH THE TOOL
engage in horseplay with the tool or point it at yourself
NEVER ASSUME THE TOOL IS EMPTY
Check the magazine for fasteners that may be left in the
never point it at anyone or yourself. Unseen fasteners
NEVER CLAMP THE TRIGGER IN A LOCKED OR
OPERATING POSITION
disabled or clamped in a locked or operating position
since this will cause the tool to drive a fastener any time
the work contacting element depressed.
DO NOT LOAD FASTENERS WITH THE AIR LINE
CONNECTED, OR WITH THE TOOL TRIGGER OR
WORK CONTACTING ELEMENT DEPRESSED
When loading fasteners into the tool be sure you
disconnect the air line and that you do not depress
the trigger or work contacting element.
OPERATE THE TOOL ONLY ON A WORKPIECE
The tool should be operated only when it is in contact
with the workpiece. Even then you should be careful
when fastening thin material or working near the edges
and corners of the workpiece since the fasteners may
drive through or away from the workpiece.
DO NOT DISABLE OR REMOVE THE WORK
CONTACTING ELEMENT
contacting element. Do not use the tool unless the work
contacting element is working properly. The tool could
DISCONNECT THE TOOL WHEN NOT IN USE
moving the tool to a new location. The tool must
never be left unattended because people who are
not familiar with the tool might handle it and injure
themselves or others.
CARRY THE TOOL ONLY BY THE HANDLE
the tool by the air hose or with the trigger depressed
since you could drive a fastener unintentionally and
injure yourself or someone else.
DO NOT WEAKEN THE TOOL HOUSING
The tool housing is a pressure vessel and should never
be weakened by having your
ʼ
area of
work or anything else stamped or engraved into its
surface.
DISCONNECT THE TOOL WHEN PERFORMING
REPAIRS AND CLEARING JAMS
attempt to clear a jam or repair a tool unless you
have disconnected the tool from the air line and removed
all remaining fasteners from the tool.
ALWAYS USE THE PROPER FITTING FOR THE
TOOL
Only
pneumatic type air connectors should be
to the
so that high pressure air in the tool is
vented to atmosphere as soon as the air line is dis-
connected.
install
E uick disconnect couplings on
the tool. Female couplings will trap high pressure air in
the tool when the air line is
leaving the
tool charged and able to drive at least one fastener.
DO NOT EXCEED THE MAXIMUM RECOMMENDED
AIR PRESSURE
.
e
r
u
s
s
e
r
p
r
i
a
d
e
d
n
e
m
m
o
c
e
r
e
h
t
t
a
y
l
n
o
l
o
o
t
e
h
t
e
t
a
r
e
p
O
Do not
the
air pressure marked on
the tool. Be sure the air pressure gauge is operating
properly and check it at least twice a day.
use any bottled air or gases such as
to
operate the tool since they could cause the tool to
INSPECT TOOL FOR PROPER OPERATION
USE ONLY PASLODE RECOMMENDED PARTS AND
FASTENERS
Use only parts and fasteners
designed and
recommended by Paslode for use in the tool and for
work to be done. Using unauthorized parts and fasteners
or modifying the tool in any way creates dangerous
situations. Replace all missing warning labels. Refer
to tool schematic for correct placement and part number.