background image

Reference Guide

013-15734A

Wireless Load Cell ±50N

PS

-

3216

®

800-772-8700 (US)

 +1 916 462 8384

www.pasco.com

[email protected]

Hardware

Introduction

The Wireless Load Cell ±50N is a combination wireless 

and

 USB sensor that connects to a computer or tablet 

device through Bluetooth, and can also connect to a 

computer with a USB cable (included). The sensor 

measures force up to ±50 newtons (N) and acceleration 

up to ±16 g (1 g = 9.8 m/s

2

). The sensor measures com

-

pression and tension forces in any component of the 

PASCO Structures Systems as a push or pull along its X 

axis and measures acceleration in three dimensions (X, 

Y, and Z). The PASCO Data Collection Software can 

show the compression or tension forces, the accelera

-

tion in X, Y, and Z, and the resultant acceleration. The 

sensor uses a micro-electromechanical system (MEMS) 

device. 

The sensor is designed to optimize the battery usage 

time. Since each sensor has a unique Device ID 

number, more than one can be connected to a computer 

or tablet at the same time. 

Data Collection Software

Power: Rechargeable Battery

or USB Cable

Connection:

ON/OFF Button

ON/OFF Button

USB Port

USB Port

Micro USB Cable

Bottom View

Top View

Device ID

Battery Status LED

USB Status LED

Front View

LOAD side 

(connected to 

internal load cell)

FIXED side

Included Equipment

Part Number

Wireless Load Cell ±50N

PS-3216

Micro USB Cable (1 meter)

PASCO Capstone

SPARKvue

Mac OS X

Mac OS X

Windows

Windows

iOS 

Android

Chromebook

Содержание PS-3216













Отзывы: