background image

www.parweld.com

Everyday Gas Regulators – 300 BAR

 

Single Stage

F

eatures

Flow rate up to 96m

3

/h (3389 ft

3

/h)

• Full 300 bar capability

•  Outlet pressure indicated on the bonnet
• Bottom entry design suited for top outlet cylinder 

www.parweld.com

14

Maximum Outlet Pressure

E700140  Argon Preset Regulator 

3.0 Bar

E700141  Argon Indicator Regulator  3.0 Bar 
E700113  1 Gauge Argon  

30 lpm flow 

E700123  2 Gauge Argon  

30 lpm flow

Flow Meters

Features

• Designed from brass bar whilst the tube 

and cover are moulded from high quality 

polycarbonate to ensure high impact 

resistance and clarity

• Calibrated to operate at an inlet 

pressure 

 

of 30PSI

• Sensitive needle valve provides easy 

adjustment and the downward facing 

outlet connection eliminates hose 

kinking.

Fittings

• Fitted with standard 

3

/89 BSP inlet and 

valves

Fittings

• Fitted with standard 

3

/89 BSP 

outlet

• Fitted with 

5

/89 BSP inlet 

connections

Stock Code 

Description 

outlet connections

 

Stock Code 

Description

706101 

Flow Meter Mixed Gas 25 lpm (MIG)

Gas flow Tester

• Designed to check gas flow at the front of Mig Torches.

Stock Code 

Description

806001  

Gas flow Tester

8.0 Accessories

8.1 Drive rolls

Wire

0.8/1.0

1.0/1.2

1.2/1.6

Mild steel

XTFR0810

XTFR1012

XTFR1216

Stainless 

Steel

XTFR0810

XTFR1012

XTFR1216

Aluminum

XTFR0810A XTFR1012A XTFR1216A

Flux cored

XTFR0810

XTFR1012

XTFR1216

Содержание XTM353SW
















Отзывы: