background image

7

30 inches

(76 cm)

CONFIGURING YOUR UNIT

You can configure your unit using a cutting head

for grass and light weeds, or a weed blade for

cutting grass, weeds, and brush up to 1 cm in

diameter. To assemble your unit, go to the sec-

tion for the desired configuration and follow the

instructions.

ASSEMBLY INFORMATION --

TRIMMER HEAD

TRIMMER

HEAD

NOTE:

Remove the blade and metal shield be-

fore attaching the plastic shield and trimmer

head. To remove blade, align hole in the dust

cup with the hole in the side of the gearbox by

rotating the blade. Insert a small screwdriver

into aligned holes. This will keep the shaft from

turning while loosening the blade nut. Remove

blade nut by turning clockwise. Remove the

screwdriver. Remove both washers and blade.

To remove metal shield, loosen and remove the

four mounting screws. See ATTACHING THE

METAL SHIELD and INSTALLATION OF THE

METAL BLADE for illustrations. Be sure to store

all parts and instructions for future use.

ATTACHING THE PLASTIC SHIELD

AND TRIMMER HEAD

WARNING:

The shield must be prop-

erly installed. The shield provides partial

protection to the operator and others from the

risk of thrown objects, and is equipped with a

line limiter blade which cuts excess line to the

proper length. The line limiter blade (on un-

derside of shield) is sharp and can cut you.

1. Remove nut from shield.

2. Insert bracket into slot on shield.

3. Pivot shield until bolt passes through hole

in bracket.

4. Reinstall nut and tighten securely with

wrench (provided).

NOTE:

If your unit has a plastic cover over

the threads on the threaded shaft, remove the

covering to expose the threads. Before instal-

ling the trimmer head, make sure the dust cup

and retaining washer are positioned on the

gearbox as shown below.

Nut

Retaining Washer

Dust Cup

Bracket

Slot

Shield

Gearbox

NOTE:

Make sure all parts are properly

installed as shown in the illustration before

installing the trimmer head.

5. Align hole in the dust cup with the hole in the

side of the gearbox by rotating the dust cup.

6. Insert a small screwdriver into aligned

holes. This will keep the shaft from turning

while tightening trimmer head.

Screwdriver

7. While holding the screwdriver in position,

thread trimmer head onto the shaft in the

direction shown on the decal (counter-

clockwise). Tighten until secure.

NOTE:

The retaining washer must be posi-

tioned with the raised section facing toward the

gearbox.

ASSEMBLY INFORMATION -- WEED

BLADE

WEED

BLADE

Содержание T330+




















Отзывы: