Partner P738 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 17

Partner P738 Скачать руководство пользователя страница 7

7

ASSEMBLY

Protective gloves (not provided) should be
worn during assembly.

ATTACHING THE BUMPER SPIKE

The bumper spike may be used as a pivot
when making a cut.
1. Loosen and remove the bar nuts and the

clutch cover from the saw.

2. Attach the bumper spike with the two

screws as illustrated.

ATTACHING THE BAR & CHAIN

(If not already attached)

WARNING

: Recheck each assem-

bly step if the saw is received assembled. Al-
ways wear gloves when handling the chain.
The chain is sharp and can cut you even
when it is not moving!
1. Loosen and remove the bar nuts and the

clutch cover from the saw.

2. Remove the plastic shipping spacer (if

present).

Clutch cover

Bar nuts

Chain adjustment tool

(Bar Tool)

Location of

shipping

spacer

3. An adjusting pin and screw is used to ad-

just the tension of the chain. It is very im-
portant when assembling the bar, that the
pin located on the adjusting screw aligns
into a hole in the bar. Turning the screw will
move the adjustment pin up and down the
screw. Locate this adjustment before you
begin mounting the bar onto the saw. See
following illustration.

Adjustment located on clutch cover

Inside
view of
clutch
cover

4. Turn the adjusting screw by hand coun-

terclockwise until the adjusting pin just
touches the stop. This should allow the
pin to be near the correct position.

5. Slide guide bar on bar bolts until guide bar

stops against clutch drum sprocket.

Guide bar

Bar bolts

6. Carefully remove the chain from the pack-

age. Hold chain with the drive links as
shown.

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Tip of
Bar

Cutters

Depth Gauge

Drive Links

7. Place chain over and behind clutch re-

tainer, fitting the drive links in the clutch
drum sprocket.

8. Fit bottom of drive links between the

teeth in the sprocket in the nose of the
guide bar.

9. Fit chain drive links into bar groove.
10. Pull guide bar forward until chain is snug

in guide bar groove. Ensure all drive links
are in the bar groove.

11. Now, install clutch cover making sure the

adjusting pin is positioned in the lower
hole in the guide bar. Remember this pin
moves the bar forward and backward as
the screw is turned.

«
...
5
6
7
8
9
...
»

Содержание P738


















Отзывы:

Нет отзывов