Partner P738 Скачать руководство пользователя страница 3

3

IDENTIFICATION OF SYMBOLS

Move ON/STOP switch to
the ON position.

Slowly press primer bulb
6 times.

Pull the starter rope
sharply 5 times with your
right hand.

Pull the starter rope sharply
with your right hand until
the engine starts.

Pull choke/fast idle lever
out to the full extent (to
the FULL CHOKE posi-
tion).

Push the choke/fast idle
lever in to the HALF
CHOKE position.

Starting Reminder

SAFETY RULES

WARNING

:

Always

disconnect

spark plug wire and place wire where it can-
not contact spark plug to prevent accidental
starting when setting up, transporting, ad-
justing or making repairs except carburetor
adjustments.
Because a chain saw is a high-speed wood-
cutting tool, special safety precautions must
be observed to reduce the risk of accidents.
Careless or improper use of this tool can
cause serious injury.

PLAN AHEAD

S

Read this manual carefully until you com-
pletely understand and can follow all safety
rules, precautions, and operating instruc-
tions before attempting to use the unit.

S

Restrict the use of your saw to adult users
who understand and can follow safety
rules, precautions, and operating instruc-
tions found in this manual.

Snug

Fitting

Clothing

Safety

Shoes

Safety Chaps

Heavy Duty

Gloves

Eye

Protection

Hearing

Protection

Safety Hat

S

Wear protective gear. Always use steel-toed
safety footwear with non-slip soles; snug-fit-
ting clothing; heavy-duty, non-slip gloves;
eye protection such as non-fogging, vented
goggles or face screen; an approved safety
hard hat; and sound barriers (ear plugs or
mufflers) to protect your hearing. Secure hair
above shoulder length.

S

Always use approved hearing protection.
Regular

users

should

have

hearing

checked regularly as chain saw noise can
damage hearing. Long--term exposure to
noise can result in permanent hearing im-
pairment.

S

Keep all parts of your body away from the
chain when the engine is running.

S

Keep children, bystanders, and animals a
minimum of 10 meters away from the work
area. Do not allow other people or animals
to be near the chain saw when starting or
operating the chain saw.

S

Do not handle or operate a chain saw
when you are fatigued, ill, or upset, or if you
have taken alcohol, drugs, or medication.
You must be in good physical condition
and mentally alert. Chain saw work is
strenuous. If you have any condition that
might be aggravated by strenuous work,
check with your doctor before operating a
chain saw.

S

Carefully plan your sawing operation in ad-
vance. Do not start cutting until you have a
clear work area, secure footing, and, if you
are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

WARNING

Long term inhalation of

the engine’s exhaust fumes, chain oil mist and
dust from sawdust can result in serious per-
sonal injury.

S

Do not operate a chain saw with one hand.
Serious injury to the operator, helpers, by-
standers or any combination of these per-
sons may result from one-handed opera-
tion.

A

chain

saw

is

intended

for

two-handed use.

S

Operate the chain saw only in a well-venti-
lated outdoor area.

S

Do not operate saw from a ladder or in a
tree, unless you are specifically trained to
do so.

Содержание P738


















Отзывы: