manualshive.com logo in svg
background image

14

REPLACEMENT OF ENGAGEMENT ROLLER BEARING SLEEVE

9

Removal

Tool

Replace the bearing sleeve
using tool 506 37 53-01.

Removal

Tool

In order to be able to replace the
bearing sleeve, it is necessary to use a
special tool produced by Partner. 
The tool’s part number is 506 37 53-01.
For 

removal

, use the complete tool

as in the illustration.
For 

assembly

, remove the long

intermediate ring.

Replaceable seals

Remove the seals using a sharp tool. 

The scraper consists of two parts,

an O-ring and a plastic ring. The O-
ring is fitted first and placed on the
outside (against the roller). The
plastic ring is first shaped around a
round object (1) and then fitted in
the bearing sleeve (2). Use a pair of
pliers that do not damage the sealing
surface, circlip pliers will do very well.
Shape the plastic ring and press it
into place with finger pressure.

Remove the sleeve

Fit the puller as shown in the illustra-
tion. The puller’s two rings are used
for removal.

Tighten the screw until the sleeve

is entirely out.

Remove the sleeve

Fit the puller as shown in the
illustration. The puller’s two
rings are used for removal.

Tighten the screw until the

sleeve is entirely out.

Assembly

Grease the tool

As the bearing sleeve is screwed in
using the tool, there is a tendency
for the sleeve to rotate in the same
direction. (This problem is illustrated
in the next picture.)

Greasing the tool’s sliding surface

minimises this tendency.

Assembly

Grease the tool

As the bearing sleeve is 
screwed in, there is a tenden-
cy for the sleeve to rotate in
the same direction.

Minimise this by greasing

the tool’s sliding surfaces.

Align the sleeve with the thread

Fit the tool, see the next illustration,
and secure the sleeve in place by
hand.

Rotate the sleeve so that its hole

lines up with the hole* in the machi-
ne body.

*) Old model = stopper screw

New model = exit duct

Align the sleeve with the
thread

Fit the tool and secure the
sleeve lightly in place.

Rotate the sleeve so that

its hole lines up with the
hole* in the machine body.

*) Old model = stopper screw

New model = exit duct

Tighten the bearing sleeve

Tighten the bearing sleeve until it
bottoms in the chassis.

Tighten the bearing 
sleeve

506 37 53-01

Old model 

New model

Old model

New model

1.

2.

Содержание K950 RING





















Отзывы: