manualshive.com logo in svg

Partner K950 CHAIN, Руководство по ремонту

Поделиться
Скачать
Partner K950 CHAIN Скачать руководство пользователя страница 14

CHAIN TENSIONER

8

13

Tensioning screw – two versions:

Old version

The tensioning screw does not have 
a support bearing or marking in the
threaded insert. When fitting, the 
screw should be turned so it fits in
the deeper setting (arrow facing the
same direction as the bar tensioning
lug).

New version

The tensioning screw has a support
bearing (A) to locate the screw more
effectively. The threaded insert has a
marking (B) that should face upward
during fitting.

The new version also fits older

machines.

Remove the lever

Lift out the cam disc to access the
screw that secures the lever.

Remove the screw.

Remove the lever

Lift out the cam disc.

Remove the screw.

Lift the locking washer to one side so
it can be removed from the lever’s
groove.

When refitting:
Note that the locking washer has a
recess that must face towards the
screw head.

Lift the locking washer to
one side so it can be removed
from the lever’s groove.

Lift out the lever.

Refitting:
Grease the lever’s contact surface
with the cover.

Lift out the lever.

Refitting:
Grease the lever’s contact
surface with the cover.

Grease the mechanism.

Grease the mechanism thoroughly
when refitting, primarily to protect it
from water and dirt.

Grease the mechanism.

Tensioning screw – two
versions:

Old version

There is no marking in the 
tensioning screw. Fit as in the
illustration – arrow pointing
towards the bar tensioning lug. 

New version

Turn the threaded insert’s
marking (B) upward. The new
version also fits older machines.

B

A

Содержание K950 CHAIN



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды