Partner K3600 MKII Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

background image

English

– 13

STARTING AND STOPPING

Starting and stopping

Starting

•

Grip the front handle with the left hand.

•

Grip the rear handle with the right hand. When you grip
the rear handle this releases the switch lock.

Stopping

The machine is stopped by releasing the switch.

!

WARNING! Note the following before
starting:

Make sure you are standing properly and
that the blade can not come into contact
with anything.

Keep people and animals well away from the
working area.

Check that the power source (the hydraulic
unit) supplies the correct oil flow and oil
pressure.

«
...
11
12
13
14
15
...
»

Содержание K3600 MKII

























Отзывы:

Нет отзывов

Похожие инструкции для K3600 MKII

Бренд: Battipav Страницы: 15

Бренд: Accessories Unlimited Страницы: 19

Norton CP514-350i

Бренд: SAINT-GOBAIN ABRASIVES Страницы: 12

Бренд: SPEWE Страницы: 19

Бренд: Niedax Страницы: 10

Бренд: AL-KO Страницы: 244

Бренд: Kaiser Страницы: 2

Бренд: Etesia Страницы: 18

Бренд: Etesia Страницы: 26

Бренд: Etesia Страницы: 48

Бренд: Olympia Tools Страницы: 2

Бренд: PAPILLON Страницы: 42

KZ-4000TP-PRO-2S

Бренд: Kasei Страницы: 32

Бренд: Garland Страницы: 148

HL40-5g Hobby Advanced

Бренд: Full Spectrum Laser Страницы: 91

Бренд: Makita Страницы: 100

Бренд: Black & Decker Страницы: 18

Бренд: Black & Decker Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды