Particle Measuring Systems MiniCapt 100R, Руководство по эксплуатации

Страница: 10 / 75

MiniCapt Remote Microbial Air Sampler Operations Manual Page ix
List of Figures
Chapter 1: Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1
Figure 1-1 MiniCapt 100R Microbial

Air Sampler and mounting bracket - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1
Figure 1-2 MiniCapt 100R Microbial Air Sampler with BioCapt Impactor sampling head and
mounting bracket - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1
Figure 1-3 LEDs on the front of a MiniCapt Remote Microbial Air Sampler - - - - - - - - - - - 1-3
Figure 1-4 Bottom view of the MiniCapt Remote Microbial Air Sampler - - - - - - - - - - - - - 1-4
Chapter 2: Unpacking and Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1
Figure 2-1 MiniCapt Remote Microbial Air Sampler attached to a mounting bracket - - - 2-5
Chapter 3: Ethernet Communications Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1
Figure 3-1 Ethernet port connectivity LED - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-4
Figure 3-2 Example for PING test - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5
Figure 3-3 Example for ipconfig command - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5
Figure 3-4 Local Area Connection Properties window- - - - - - - - - - - - - - - - - - - - - - - - - - 3-7
Figure 3-5 Internet Protocol (TCP/IP) Properties window with IP address and subnet mask
defined- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-8
Chapter 4: Configuring for Ethernet - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
Chapter 5: Modbus Protocol - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
Chapter 6: Accessories- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-1
Figure 6-1 Sampler head on MiniCapt- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2
Figure 6-2 Sampler head off of MiniCapt - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2
Figure 6-3 Plate holder exposed - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2
Figure 6-4 Agar plate on the plate holder with agar plate lid still in place- - - - - - - - - - - - 6-3
Figure 6-5 Sampler head re-installed over the agar plate - - - - - - - - - - - - - - - - - - - - - - - - 6-3
Figure 6-6 Compressed Gas Kit components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-4
Figure 6-7 Compressed Gas Solenoid connector on the bottom of the

MiniCapt Remote Microbial Air Sampler - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-5
Figure 6-8 Isolator Monitoring Kit components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-6
Figure 6-9 Remote ISP Sampling Kit components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-7
Figure 6-10 Dual Connection BioCapt Impactor over the agar plate on the MiniCapt - 6-8
Chapter 7: Maintenance and Performance Checks- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-1
Chapter 8: Cleaning Procedures - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-1