Parsun T2CBMS Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 47

background image

31

4. Transporting and storing

4.1 Transporting

The outboard motor should be trailed and stored in the normal running position. If there is insufficient road

clearance in this position, then trailer the outboard motor in the tilt position using a motor support device.

CAUTION:

Do not use the tilt support lever or knob when trailing the boat. The outboard motor could shake

loose from the tilt support and fall.

WARNING:



Never get under the lower unit while it is tilted, even if a motor support bar is used.



Please put the outboard motor as shown figures below when transporting or storing it.

CAUTION:

Place a towel or something similar under the outboard motor to protect it from damage.

«
...
36
37
38
39
40
...
»

Содержание T2CBMS
















































Отзывы:

Нет отзывов

Похожие инструкции для T2CBMS

PIC18F57Q43 Curiosity Nano

Бренд: Microchip Technology Страницы: 34

Бренд: JETWAY Страницы: 46

Бренд: MSI Страницы: 169

KEEX-1850 Series

Бренд: Quanmax Страницы: 61

Бренд: Linear Technology Страницы: 7

Бренд: IBASE Technology Страницы: 72

Бренд: Intel Страницы: 26

Spartan-7 SP701

Бренд: Xilinx Страницы: 4

i.MX 8M Mini SODIMM SOM

Бренд: iWave Страницы: 16

Бренд: Supermicro Страницы: 97

Бренд: Gigabyte Страницы: 74

NVIDIA MS-7504PV

Бренд: MSI Страницы: 50

Бренд: Ublox Страницы: 32

Бренд: DFI Страницы: 80

Бренд: DFI Страницы: 134

Fatal1ty Z77 Professional-M

Бренд: ASROCK Страницы: 245

X58A-GD65 series

Бренд: MSI Страницы: 100

RouterBOARD 500r5 Series

Бренд: MikroTik Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды