Parsun T2.6CBMS Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 47

background image

36

5.3 Treatment of submerged motor

If the outboard is submerged, take it to a PARSUN dealer. Otherwise some corrosion may begin almost
immediately.

1. Thoroughly wash away contaminants with fresh water.

2. Remove the spark plug(s), and then face the spark plug hole downward to allow any mud, or contaminants
to drain.

3. Fill the sump with fresh engine oil.

4. Feed engine fogging oil or engine oil through the carburetor(s) and spark plug holes while starting the
engine.

5. Take the outboard motor to a PARSUN dealer as soon as possible.

CAUTION:

Do not attempt to run the outboard motor until it has been completely inspected.

«
...
41
42
43
44
45
...
»

Содержание T2.6CBMS
















































Отзывы:

Нет отзывов

Похожие инструкции для T2.6CBMS

Бренд: EPOX Страницы: 54

PowerSoC CY3267

Бренд: Cypress Страницы: 12

Бренд: MSI Страницы: 169

JW-A880GM-FUSION

Бренд: J&W Страницы: 38

Бренд: JETWAY Страницы: 18

Бренд: Sleipner Страницы: 28

Бренд: Gigabyte Страницы: 96

Бренд: Aaeon Страницы: 119

Бренд: LanParty Страницы: 141

Бренд: Analog Devices Страницы: 7

Бренд: TYAN Страницы: 86

Бренд: Texas Instruments Страницы: 21

Бренд: ASROCK Страницы: 98

Бренд: ASROCK Страницы: 65

Бренд: AOpen Страницы: 8

Бренд: Asus Страницы: 84

Бренд: Asus Страницы: 49

Бренд: ST Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды