Parsun T2.6CBMS Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 47

background image

11

2.5 Starting engine

1. Loosen the air vent screw on the fuel tank cap, 2 or 3 turns.

2. Open the fuel cock.

WARNING:



Do not attach the lanyard to clothing that could tear loose. Do not route the lanyard
where it could become entangled, preventing it from functioning.



Avoid accidentally pulling the lanyard during normal operation. Loss of engine
power means the loss of steering control. Also, without engine power, the boat could
slow rapidly. This could cause people and objects in the boat to be thrown forward.

«
...
16
17
18
19
20
...
»

Содержание T2.6CBMS
















































Отзывы:

Нет отзывов

Похожие инструкции для T2.6CBMS

Бренд: Yamaha Страницы: 232

RouterBOARD 411

Бренд: 4gon Страницы: 2

SPC572LADPT100S

Бренд: ST Страницы: 29

Бренд: Biostar Страницы: 65

Бренд: Xilinx Страницы: 56

Бренд: DFI Страницы: 5

Бренд: Gigabyte Страницы: 100

Бренд: Gigabyte Страницы: 31

LCMXO3L-DSI-EVN

Бренд: Lattice Страницы: 2

FRDMDUALK3664EVB

Бренд: NXP Semiconductors Страницы: 17

Бренд: Icop Страницы: 31

Бренд: Supermicro Страницы: 109

Бренд: JETWAY Страницы: 51

IN440 Micro-ATX

Бренд: trimond Страницы: 47

Бренд: MSI Страницы: 445

Бренд: ASROCK Страницы: 71

Бренд: ASROCK Страницы: 2

Бренд: JETWAY Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды