Please note that it is forbidden to apply a VIH on an unpowered GPIO, so when its VDDO isn’t
supplied.
5.3.2
I2C
Supports 100kb/s, 400kb/s, 1Mb/s and 3,4M
slave mode,
I2C is an Open Drain protocol. External pull
supplied if the corresponding VDDO to the I2C pads isn’t powered.
•
I2C_1
I2C_1 is a 3,3V signaling I2C link dedicated to be used on motherboard,
It can operate as a master or as a slave,
Note: On WB_FC7xxx development board, I2C_0 is used for Touch Panel Controller, external audio
codec & audio power amplifier interface,
•
I2C_2
I2C_2 is 3,3V signaling at the connector end,
It can operate as a master or as a slave,
Note: On WB_FC7xxx board, I2C_1 is used for iPOD authentication chip communication,
5.3.3
UART
The UARTs
are Universal Asynchronous Receiver
with communication standards such as EIA, RS
interface is 3MHz, with flow control signals.
•
UART_0 :
UART 0 is a standard UART interface (Rx & Tx signals), with flow control signals
(RTS & CTS),
•
UART_5, 6 and 7
have only Rx and Tx signals,
5.3.4
5.3.4
5.3.4
5.3.4
5.3.4
5.3.4
5.3.4
5.3.4
PWM
Up to 16 PWM outputs are available. They support frequencies from 0,06Hz to 65MHz with a
programmable duty cycle or from 3,97kHz to 130MHz with a 50% duty cycle.
5.3.5
SDIO
SDIO_1 is a complete SD Card bus, compliant
It supports SD High Capacity (SDHC), SD High Speed (SDHS) and SD eXtended Capacity
standard.
It is also used as secondary flash update interface.
Confidential Information
Please note that it is forbidden to apply a VIH on an unpowered GPIO, so when its VDDO isn’t
Supports 100kb/s, 400kb/s, 1Mb/s and 3,4Mb/s speeds in master mode and 100kb/s, 400kb/s in
I2C is an Open Drain protocol. External pull-up to VDDO are needed. The pull
supplied if the corresponding VDDO to the I2C pads isn’t powered.
C link dedicated to be used on motherboard,
It can operate as a master or as a slave,
Note: On WB_FC7xxx development board, I2C_0 is used for Touch Panel Controller, external audio
codec & audio power amplifier interface,
the connector end,
It can operate as a master or as a slave,
Note: On WB_FC7xxx board, I2C_1 is used for iPOD authentication chip communication,
are Universal Asynchronous Receiver-Transmitter, commonly used in conjunction
with communication standards such as EIA, RS-232, RS-422 or RS-485. The maximum speed of this
interface is 3MHz, with flow control signals.
UART 0 is a standard UART interface (Rx & Tx signals), with flow control signals
have only Rx and Tx signals,
Up to 16 PWM outputs are available. They support frequencies from 0,06Hz to 65MHz with a
programmable duty cycle or from 3,97kHz to 130MHz with a 50% duty cycle.
bus, compliant with SDIO v3.0 specification part.
upports SD High Capacity (SDHC), SD High Speed (SDHS) and SD eXtended Capacity
It is also used as secondary flash update interface.
26/39
Ref: OEM-2012-149
Please note that it is forbidden to apply a VIH on an unpowered GPIO, so when its VDDO isn’t
b/s speeds in master mode and 100kb/s, 400kb/s in
up to VDDO are needed. The pull-up shouldn’t be
Note: On WB_FC7xxx development board, I2C_0 is used for Touch Panel Controller, external audio
Note: On WB_FC7xxx board, I2C_1 is used for iPOD authentication chip communication,
d in conjunction
485. The maximum speed of this
UART 0 is a standard UART interface (Rx & Tx signals), with flow control signals
Up to 16 PWM outputs are available. They support frequencies from 0,06Hz to 65MHz with a
upports SD High Capacity (SDHC), SD High Speed (SDHS) and SD eXtended Capacity (SDXC) cards
Содержание FC7100
Страница 1: ...Confidential information PARROT PRODUCT DATASHEET FC7100 Version 2 6 August 2014 ...
Страница 15: ...Confidential Information 4 4 FC7100 integrated into the headunit Information 15 39 Ref OEM 2012 149 ...
Страница 31: ...6 Mechanical 6 1 Outline dimensions Weight 51 g Confidential Information 31 39 Ref OEM 2012 149 ...