PARKZONE Radian Pro, Инструкция по эксплуатации

Страница: 10 / 15

10
EN
Replacement Parts and Optional Parts
Number Description
EFLA1030 30-Amp Pro Switch-Mode BEC Brushless ESC
PKZ5401 Optional Flap Set: Radian Pro
PKZ5467 Bare Fuselage without Canopy: Radian Pro
PKZ1017 Propeller 9.75 x 7.5_1: Radian
PKZ1018 Prop Adapter & Spinner Set:Radian
PKZ1033 11.1V 1300mAh LiPo Bat with EC3 Connector
PKZ1040 2-3 DC LiPo Balancing Charger
PKZ4713 Canopy: Radian
PKZ4714 Firewall w/Screws: Radian
PKZ4716 480B Outrunner BL Motor: Radian
PKZ4725 Horizontal Tail: Radian
PKZ5402 Decal sheet: Radian Pro
PKZ5403 Aileron servo extension: Radian Pro
PKZ5404 Flap servo extension (305mm)
PKZ5420 Main wing: Radian Pro
PKZ5422 Pushrod set: Radian Pro
PKZ1081 SV80 long lead 3-wire servo
PKZ1090 DSV130 3 wire digital servo metal gear
PKZ1060 Mini servo (3W ) with arms, short lead
Number Description
EFLA110 Power Meter (optional)
EFLA253 Hex Driver, 1.5mm (optional)
EFLA257 Screwdriver, #0 Phillips (optional)
EFLA258 Screwdriver, #1 Phillips (optional)
EFLAEC301 EC3 Device Connector, Male (2) (optional)
EFLAEC302 EC3 Device Connector, Female (2) (optional)
EFLAEC303 EC3 Device/Battery Connector, Male/Female (optional)
EFLC505 1- to 5-Cell Li-Po Battery Charger with Balancer (optional)
SPMAR600 DSM2 5-Channel Sport Receiver (optional)
SPMAR6200 DSM2 6-Channel Sport Receiver (optional)
SPMR5500 DX5e 5-Channel Transmitter Only (optional)
SPMR6600 DX6i 6-Channel Transmitter Only (optional)
SPMR7700 DX7 7-Channel Transmitter Only (optional)
Problem Possible Cause Solution
Aircraft will not respond to throttle but
responds to other controls
• Throttle not at idle at control setup so throttle
not armed
• Throttle channel is reversed
• Bind with throttle stick and throttle trim at
lowest setting
• Reverse throttle channel on transmitter
Extra propeller noise or extra vibration
• Damaged propeller, motor or motor mount
• Loose propeller and spinner
• Propeller blades installed backwards • Replace damaged parts
• Tighten parts for propeller and spinner
• Remove and install propeller blades correctly
Reduced flight time or aircraft
underpowered
• Flight battery charge is low
• Propeller blades installed backwards
• Flight battery damaged • Completely recharge flight battery
• Remove and install propeller blades correctly
• Replace flight battery and obey flight battery
instructions
LED on receiver flashes rapidly with bind
plug installed and aircraft will not link to
transmitter
• Transmitter too near aircraft during
binding process
• Aircraft not bound to transmitter
• Aircraft bound to different model memory
(ModelMatch radios only)
• Low charge in transmitter batteries
• Disconnect then reconnect flight battery
to aircraft
• Move transmitter a few feet from aircraft,
disconnect and reconnect flight battery to
aircraft and re-bind
• Bind transmitter to aircraft receiver
• Select correct model memory on transmitter
• Replace or charge transmitter batteries
Control surface does not move, or is slow
to respond to control inputs.
• Control surface, control horn, linkage or
servo damage
• Wire damaged or connections loose
• Parts not secured in fuselage
• Replace or repair damaged parts and
adjust controls
• Do a check of wires and connections for lose
wiring, connect or replace as needed
• Make hook and loop fastenings tight so no parts
move in fuselage
Controls reversed
• Channels need to be reversed in receiver • Do the Control Direction Test and adjust controls
on transmitter appropriately
Motor loses power
• Damage to motor, or power components • Do a check of batteries, transmitter, receiver,
ESC, motor and wiring for damage (replace as
needed)
Motor power pulses then motor loses
power • ESC uses default soft Low Voltage Cutoff (LVC) • Recharge or replace flight battery
Troubleshooting Guide
To purchase directly from Horizon Hobby, please visit www.horizonhobby.com
or call Horizon’s Consumer Sales Division: (800) 338-4639