13
GB/CY
Switching off:
Release the ON / OFF switch
3
.
Setting the cutting angle
You can set the cutting angle accurately with the
help of the cutting angle scale
12 b
.
Release the wing screws / locking bolts of the
cutting angle preselector
9
on both sides, set
the desired angle on the cutting angle scale
12 b
and retighten the wing screws / locking bolts.
Setting the cutting depth
Note:
If possible we recommend that the cutting
depth is set approximately 3 mm greater than the
material thickness. This should help to ensure you
achieve a clean cut.
Release the wing screw on the cutting depth
setting clamp
5
, set the required cutting depth
on the scale
19
and retighten the wing screw.
Setting the guide fence
Release the wing screw
13
of the base plate
8
and insert the guide fence
15
into the slot
14
.
Retighten the wing screw
13
.
Switching the laser on and off
Switching on:
Move the laser ON / OFF switch
11
to setting “I”.
Switching off:
Move the laser ON / OFF switch
11
to setting “0”.
Note:
If the batteries are exhausted replace them
with two 1.5 V alkaline batteries LR44 (e.g. GPA 76).
Working with the circular saw
1. Switch on the device as described in the section
about “Switching on and off” and then place it
first with the front edge of the base plate
8
against the material.
2. Align the device using the guide fence
15
or
with reference to marked-out line or by using
the laser.
3. Hold the machine with both hands by the
handles (see Fig. A) and saw the material
with moderate pressure.
Setting the speed
Turn the wheel
1
to the desired speed setting
(arrow marking
)
(1 = lowest speed / 6 = highest speed):
Use the general settings suggested in the following
table (information offered without liability) or adjust
the speed setting on the setting wheel
1
to the
material being cut.
Material
Speed
setting
Hard- and softwood (solid wood)
cut longitudinally and transversely
6
Plywood, hard fibre board
6
Chipboard
6
Blockboard, laminated wood
6
Coated and veneered board
6
PVC board
3-5
Acrylic glass panels, Plexiglas
2-4
Aluminium board
4-6
Aluminium profiles
4-6
Plasterboard
1-2
Mineral wool board
1-2
Cement-bound chipboard
1-2
The circumferential speeds at minimum and maximum
rotational speeds are approx.:
Setting
Rpm
Metres/ sec
1
2200
21.8
6
5200
51.7
Preparing for use
Содержание PHKS 1300 A1
