11
GB/IE/CY
Bringing into use / Maintenance and cleaning / Service centre / Warranty
and stop the spraying process approximately
10 cm outside the surface to be sprayed.
NOTE:
The distance between the nozzle and
the workpiece depends on the material being
sprayed (approx. 20 to 35 cm spraying dis-
tance, depending on the spray cone and the
desired amount of material to be applied).
Use the device in a horizontal orientation only
(as shown in Fig. D).
Carry out a trial in each case to determine the
most effective spraying distance.
Start with a longer distance.
3. Spray corners or small decorative details first
using short bursts of spray.
Then go on to the actual spraying process.
4. The spray process should follow the sequence
shown in Fig. E – keep the spray gun moving
parallel to the surface
– Do not incline the spray gun
– Move the spray gun at a constant speed
– Apply the sprayed medium as thinly as possible
– The layer(s) of sprayed medium need(s) to
be allowed to dry for some time before you
apply the next coat Fig. F) at right angles to
the previous coat.
5. Do not allow the paint cup
7
to empty com-
pletely while spraying – drops may form!
Maintenance and cleaning
General advice:
1.
WARNING!
Pull out the mains plug be-
fore you carry out any tasks on the spray gun.
Do the same when you take a break from spraying.
2. After each use, spray thinners
(in the open
air only – danger of explosion!)
or
water through the device.
3. To protect from rust after cleaning, you can
spray sewing machine oil through the device.
4.
WARNING!
DANGER TO LIFE
THROUGH ELECTRIC SHOCK!
Never im-
merse the device in the cleaning medium.
5. Never use inflammable solvents to clean the
device.
6. Use a dry cloth to clean the housing. Never
use petrol, solvents or cleaning agents that
might attack plastic.
Cleaning instructions:
1. Unscrew the attachment screw
1
, see Fig. A.
2. Take off the pump housing
10
downwards.
3.
Unscrew
nozzle
8
and remove the suction-
pressure valve
9
.
4. Take the pump piston
4
and spring
5
out of
the pump housing
10
.
5. Clean
parts
4
,
5
,
8
,
9
with thinners.
6. Fit the components back in reverse order.
TIP:
After use or cleaning, hang up the electrical
power tool from the metal stirrup
14
.
Service centre
WARNING!
Have your electrical
power tool repaired only by qualified
specialist personnel using original man-
ufacturer parts only.
This will ensure that
your electrical power tool remains safe to use.
WARNING!
If the plug or mains
lead needs to be replaced, always
have the replacement carried out by
the manufacturer or its service centre.
This will ensure that your electrical power tool
remains safe to use.
Warranty
The warranty for this appliance is for 3
years from the date of purchase. The ap-
pliance has been manufactured with care
and meticulously examined before deliv-
ery. Please retain your receipt as proof
of purchase. In the event of a warranty
claim, please make contact by telephone
with our Service Department. Only in this
way can a post-free despatch for your
goods be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for
private use only and is not intended for commercial
use.
Содержание PFS 100 A1
