PEH 30 C3
GB
│
IE
│
NI
│
CY
│
9
■
♦
Push the planing blade sideways out of the
clamping element (see fig . D)
NOTE
►
The planing blade may be factory-bonded
with protective lacquer . It is not necessary to
re-bond the blade .
♦
Fit either a new or turned blade in the reverse
order . Make sure that the notch on the planing
blade slides into the tensioning plate
groove
20a
(see fig . E) .
♦
Make sure that the planing blade protrudes
a little way (approx . 1 mm) from the cutter
block in the direction of the movable lateral
cutter block guard . Carefully turn the cutter
block to check that the planing blade does not
touch anything .
♦
Also ensure that the clamping element
closes flush to the cutter block . The clamping
element must contact the hex screws
18a
before the fastening screws can be tight-
ened .
♦
Planing blades can be purchased exclusively
from the address given below (see section
“Service”) . Do not use planing blades from
other manufacturers .
Setting the planing blade height
♦
Set the cutting depth to 0 mm .
♦
Check the position of the planing blade at
both ends . Use a flat, straight object as a guide
strip over the plane sole .
♦
The tip of the planing blade must be flush
with the surface of the plane sole .
♦
The height of the planing blade can be
adjusted using the hex key via the two hex
screws
18a
. Adjust the two hex screws
18a
so that
the tip of the planing blade is flush with the
plane sole on both sides .
Replacing the drive belt (see fig . F)
WARNING! RISK OF INJURY!
►
Always remove the plug from the power
socket before working on the appliance .
♦
Remove the screws and detach the drive
belt cover .
♦
Remove the worn drive belt .
♦
Fit the new drive belt onto the small belt
wheel first and then turn the drive belt
and pull it onto the large belt wheel .
♦
Replace the drive belt cover and fix it in
place using the screws .
Maintenance and cleaning
WARNING! RISK OF INJURY!
►
Always remove the plug from the power
socket before working on the appliance .
♦
Keep the appliance and the ventilation slits
clean to ensure fault-free operation .
♦
Clean the chip ejector regularly .
♦
To clean a blocked chip ejector, use a suitable
tool (e .g . a piece of wood, compressed air,
etc .) .
♦
Use a dry cloth to clean the housing .
♦
Use a brush to remove any dust stuck to the
appliance .
♦
Never use sharp objects, petrol, solvents or
cleansers which can damage plastic . Do not
allow any liquids to get into the interior of the
appliance .
NOTE
►
Spare parts which are not listed (e .g . carbon
brushes, planing blades) can be ordered
exclusively via our Service Hotline .
Содержание PEH 30 C3
