Parkside 352083 2007, Оригинальное руководство пользователя

Страница: 50 / 78

PBK 4 A2
GB │ MT │
45 ■
■ Always trim and cut using the high speed range. Do not let the engine
run at a low speed when starting to mow or trim.
■ When starting and operating the tool, ensure that it does not come into
contact with the ground, stones, wire or other foreign material.
Switch off the tool before you put it down.
■ Switch off the tool before you put it away.
■ Always switch the engine off before working on the cutting tool.
Operational safety instructions for cutting blades
Preparation
■ The cutting blade flings objects and soil with great force. They can
cause blindness or other injuries. Wear eye, face and leg protection.
Always remove objects from the work area before using the cutting
blade.
■ The cutting blade continues running after the throttle lever has been
released. A running-down cutting blade can inflict cuts to yourself or
other people standing nearby. Switch the engine off and make sure that
the cutting blade has come to a complete stop before performing any
work on the cutting blade.
Personal safety
■ The tool can cause blindness or other injuries to bystanders. Maintain
a minimum distance of 15 metres in all directions between the tool and
other people or animals.
Use and handling
■ Do not use the tool if any of the cutting blade accessories have not
been properly installed.
■ The cutting blade can kick back from objects with force. It can cause
injuries to your arms and legs. If the tool comes into contact with a
foreign body, immediately shut down the engine and wait until the
cutting blade has come to a complete stop. Check the cutting blade for
damage. Always replace the cutting blade if it is bent or cracked.
Safety devices/equipment
The corresponding plastic protective guard for the cutting blade or filament
operation must be installed when working with the tool in order to prevent
objects from being flung away.
WARNING!
■ Never mow/trim while other individuals, especially children or
animals, are in the vicinity.
■ Maintain a safety distance of 15 m. Switch off the tool immediately if
this distance is not maintained.
ATTENTION! RISK OF POISONING!
■ Exhaust gases, fuels and lubricants are toxic. Exhaust gases must
never be inhaled.
WARNING!
■ Petrol is highly flammable. Store petrol only in the containers provid-
ed.
■ Refuel only outdoors and do not smoke.
■ The filler cap must not be opened and refuelling must not take place
while the engine is running or when the tool is hot.
■ Do not attempt to start the engine if the petrol has overflowed.
Instead, remove the tool from the area polluted by petrol. Do not
attempt to restart the tool until the petrol fumes have dissipated.
■ For safety reasons, the petrol tank and filler cap must be replaced if
they are damaged.
Limit the noise generation and vibrations to a minimum!
■ Only use tools that are in good condition.
■ Maintain and clean the tool on a regular basis.
■ Adapt your working method to the tool.
■ Do not force the power tool.
■ Have the tool inspected, if necessary.
■ Switch the tool off when not in use.
■ Wear protective gloves.
Before use
ATTENTION!
■ Always wear non-slip footwear and appropriate safety clothing
such as protective gloves, a hard hat, a protective mask and safety
goggles as well as ear muffs.
■ Check the area in which the tool is to be used and remove any
objects that may be caught and slung away.
■ Before each use and after dropping it or other impacts, always
visually inspect the tool to check whether the cutting tool, mounting
bolts and the entire cutting unit is damaged. Worn or damaged
cutting tools and mounting bolts must be replaced.
■ Always carry out a visual inspection before use to check whether the
cutting tools are worn or damaged. To prevent imbalance, worn or
damaged cutting tools and mounting bolts should only be replaced
as complete sets.
Attaching the round handle
♦ Start by fitting the rubber ring
4a
on the boom .
♦ Attach the round handle , as shown in the diagram, onto the rubber
ring
4a
from above.
♦ Now press the clamping shell
4
b of the round handle onto the
rubber ring
4a
of the boom from below.
♦ Insert the locking screw and tighten it.
Fitting the quick release mechanism
♦ Hook in the carabiner and secure it with the red strap on the quick
release mechanism (see illustrations). Pull on the red strap if you
have to release the tool quickly.