Parkside 315340 Скачать руководство пользователя страница 15

Страница: 15 / 68

GB/IE/NI

• Before making a cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to angle

the machine head (4) to the left, until the pointer (19) indi-
cates the desired angle measurement on the scale (18).

• Re-tighten the set screw (22).
• Cut as described in section 8.3.

8.7 Mitre cut 0°- 45° and turntable 0°- 45°

(fig. 2/4/12)

The sliding compound mitre saw can be used to make mitre
cuts to the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).

Attention! For mitre cuts (inclined saw head), the

left side

the moveable stop rails (16a) must be fixed in the outer position.
• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) outwards.

• The moveable stop rail (16a) must be fixed far enough in

front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.

• Before making a cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Fold the locking handle (11) upwards to loosen the rotary

table (14).

• Set the rotary table (14) to the desired angle (refer also to

point 8.4 in this regard).

• Fold the locking handle (11) downwards to secure the rotary

table (14).

• Undo the set screw (22).
• Use the handle (1) to tilt the machine head (4) to the left until

it coincides with the required angle value (in this connection
see also section 8.6).

• Re-tighten the set screw (22).
• Cut as described under section 8.3.

8.8 Limiting the cutting depth (fig. 3/13)

• The cutting depth can be infinitely adjusted using the screw

(24). To do this loosen the knurled nut (24a) on the screw
(24). Turn the screw (24) in or out to set the required cutting
depth. Then re-tighten the knurled nut (24a) on the screw
(24).

• Check the setting by completing a test cut.

8.9 Chip collection bag (fig. 1/20)

The saw is equipped with a debris bag (17) for sawdust and chips.
Attention! The chip collection bag may only be used when cutting
wood and wood-like materials!
Squeeze together the metal ring on the dust bag and attach it
to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zipper at
the bottom.

Connection to an external dust extractor

For dust extraction, a vacuum hose can also be connected to
the dust extraction spout.
• Connect the vacuum hose with the dust extraction spout.
• The industrial vacuum cleaner must be suitable for the mate-

rial being worked.

• When vacuuming dust that is especially detrimental to health

or carcinogenic, use a special vacuum cleaner.

8.10 Changing the saw blade (fig. 1/2/14-16)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!

• Swing the machine head (4) upwards and lock with the lock-

ing bolt (23).

• Fold the saw blade guard (5) upwards.
• Use one hand to insert the Allen key (C) in the flange screw

(28).

• Firmly press the saw shaft lock (30) and slowly rotate the

flange screw (28) in clockwise direction. The saw shaft lock
(30) engages after no more than one rotation.

• Now, using a little more force, slacken the flange screw (29)

in the clockwise direction.