Parkside 276436, Руководство по эксплуатации и технике безопасности

Страница: 8 / 76

GB 3
*S6, continuous operation periodic duty.
Identical duty cycles with a period at load followed by a
period at no load. Running time 10 minutes; duty cycle is
25% of the running time.
The work piece must have a minimum
height of 3mm and a minimum width of 10
mm.
Make sure that the workpiece is always se-
cured with the clamping device.
Information about noise development
The noise levels of this machine during operation are as
follows:
L
pA
: 99.6dB(A) K=3dB(A)
L
wA
: 112.6dB(A) K=3dB(A)
Warning:
Noise can have serious e ff ects on your health.
If the machine noise exceeds 85 dB (A), please wear suitable
hearing protection. If the electrical connection is defective,
the power can fail when starting the machine. This could in-
fl uence other machines (e.g. blinking lamps). If the electrical
power corresponds to Zmax < 0.27, such disruptions should
not occur. (However, if they do, inform your specialist dealer).
• The speci
fi ed vibration emission value has been meas-
ured according to a standardised testing procedure and
can be used for comparison of one electric tool with
another;
• The speci fi ed vibration emission value can also be used
for an initial assessment of the load.
Proper use
The mitre saw is used for the cutting of wood and plastic,
according to the machine size.
Warning!
The supplied saw blade is only intended for
the sawing of wood! Do not use this blade for the sawing
of plastic!
The saw is not suitable for the cutting of
fi rewood.
The machine may only be used in the intended manner.
Only suitable saw blades may be used for the machine.
The use of any type of cutting wheels is prohibited.
An element of the intended use is also the observance of
the safety instructions, as well as the assembly instructions
and operating information in the operating manual.
Persons who operate and maintain the machine must be
familiar with the manual and must be informed about po-
tential dangers.
Any use beyond this is improper. The user/operator, not the
manufacturer, is responsible for damages or injuries of any
type resulting from this.
In addition, the applicable accident prevention regulations
must be strictly observed.
Other general occupational health and safety-related rules
and regulations must be observed.
The liability of the manufacturer and resulting damages are
excluded in the event of modi
fi cations of the machine.
Despite use as intended, speci fi c risk factors cannot be
entirely eliminated. Due to the design and layout of the ma-
chine, the following risks remain:
• Contact with the saw blade in the non-covered saw
area.
• Reaching into the running saw blade (cutting injury).
• Kick-back of workpieces and workpiece parts.
• Saw blade breakage.
• Ejection of faulty carbide parts of the saw blade.
• Hearing damage when the necessary hearing protection
is not used.
• Harmful emissions of wood dusts during use in enclosed
areas.
Please observe that our equipment was not designed with
the intention of use for commercial or industrial purposes.
We assume no guarantee if the equipment is used in com-
mercial or industrial applications, or for equivalent work.
Important information
Attention!
The following basic safety measures must be
observed when using electric tools for protection against
electric shock, and the risk of injury and
fi re. Read all these
notices before using the electric tool and keep the safety
instructions for later reference.
Safe work
1
Keep the work area orderly
– Disorder in the work area can lead to accidents.
2
Take environmental in fl uences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or wet environ-
ment.
– Make sure that the work area is well-illuminated.
– Do not use electric tools where there is a risk of fi re or
explosion.
3
Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g. pipes,
radiators, electric ranges, cooling units).
4
Keep other persons away
– Do not allow other persons, especially children, to
touch the electric tool or the cable. Keep them away
from your work area.
– The operating person must be at least 18 years of
age; trainees must be at least 16 years, however only
under supervision.
5
Securely store unused electric tools
– Unused electric tools should be stored in a dry, el-
evated or closed location out of the reach of children.
6
Do not overload your electric tool
– They work better and more safely in the speci fi ed
output range.
7
Use the correct electric tool
– Do not use low-output electric tools for heavy work.
– Do not use the electric tool for purposes for which it
is not intended. For example, do not use handheld
circular saws for the cutting of branches or logs.
– Do not use the electric tool to cut fi rewood.
8
Wear suitable clothing
– Do not wear wide clothing or jewellery, which can
become entangled in moving parts.
– When working outdoors, anti-slip footwear is recom-
mended.