4
PROTECTIVE
EARTH GROUND
CONNECTOR
POWER
1
2
+
COMMO
N
24V 20%
-
3
RS485
COMMS
PORT
N/
C
PORT
COMMS
RS232
PGM PORT
RS232
(NIC)
(OPTIONAL)
ETHERNET
ETHERNET
AUXILIARY
TYPE B
USB
1 2 3 4
USB HOST
Rx
Tx
B
Tx
A
(PIN 8)
TxB (PIN 1)
R
TS (PIN 6)
TxEN
Tx
A
Rx
A
Rx
B
COMM
Tx COMM COMM
CTS (PIN 1)
Rx
R
TS (PIN 6)
Tx COMM COMM
CTS (PIN 1)
TS8010 PORT PIN OUTS
CONFIGURING A TS8010
The TS8010 is configured using DSI8000 software. DSI8000 is available as a
free download from Parker - SSD Drives’ website. Updates to DSI8000 for new
features and drivers are posted on the website as they become available. By
configuring the TS8010 using the latest version of DSI8000, you are assured that
your unit has the most up to date feature set. DSI8000 software can configure the
TS8010 through the RS232 PGM port, USB port, or CompactFlash.
The USB port is connected using a standard USB cable with a Type B
connector. The driver needed to use the USB port will be installed with DSI8000.
If this driver has not been installed, it can be downloaded from the website.
The RS232 PGM port uses a programming cable made by Parker - SSD
Drives to connect to the DB9 COM port of your computer. If you choose to
make your own cable, use the “TS8010 Port Pin Out Diagram” for wiring
information.
The CompactFlash can be used to program a TS by placing a configuration
file and firmware on the CompactFlash card. The card is then inserted into the
target TS and powered. Refer to the DSI8000 literature for more information on
the proper names and locations of the files.
ACCESSING THE COMPACTFLASH CARD
VIA USB DEVICE PORT
In order to access data from the CompactFlash card via the USB device port,
a driver must be installed on your computer. This driver is installed with
DSI8000 and is located in the folder C:\Program Files\Parker\DSI8000\Device\
after DSI8000 is installed. This may have already been accomplished if your
TS8010 was configured using the USB port.
Once the driver is installed, connect the TS8010 to your PC with a USB cable,
and follow the “Mounting the CompactFlash” instructions found in the DSI8000
user manual.
ETHERNET COMMUNICATIONS
Ethernet communications can be established at either 10 BASE-T or 100
BASE-TX. The TS8010 unit’s RJ45 jack is wired as a NIC (Network Interface
Card). For example, when wiring to a hub or switch use a straight-through cable,
but when connecting to another NIC use a crossover cable.
The Ethernet connector contains two LEDs. A yellow LED in the upper right,
and a bi-color green/amber LED in the upper left. The LEDs represent the
following statuses.
The DSI8000 manual contains additional information on Ethernet
communications.
RS232 PORTS
The TS8010 has two individually isolated RS232 ports. There is the PGM
port and the COMMS port. Although only one of these ports can be used for
programming, both ports can be used for communications with a PLC.
The RS232 PGM port can be used for either master or slave protocols with
any TS8010 configuration.
c
ommunicating
w
ith
the
tS8010
WARNING - DO NOT CONNECT OR DISCONNECT CABLES
WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE
NON-HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND
DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT
CONNECTION.
LED COLOR
DESCRIPTION
YELLOW solid
Link established.
YELLOW flashing
Data being transferred.
GREEN
10 BASE-T Communications
AMBER
100 BASE-TX Communications
