Parker PGBC-5200 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 31

Parker PGBC-5200 Скачать руководство пользователя страница 2

3

2

INTRODUCTION

CONTENTS

This manual has been produced by Parker Products Ltd. and should be kept with the

product and referenced for operation, maintenance and troubleshooting.

This manual contains an overall description of the product, together with all the

necessary information for using the product correctly and safely. It is highly

recommended that this manual is read prior to any operation or maintenance of this product.

The safety precautions and warnings are to ensure your safety and protect you from harm or

damage to the product.

All photographs and drawings in this manual are supplied by Parker Products Ltd. to help you

with the operation and maintenance of the product. The information contained in this manual

was accurate at the time of production, however Parker Products Ltd. may make modifications to

the product without notification.

GENERAL SAFETY ..................................................................................... 4-5
SAFETY SYMBOLS ..................................................................................... 6-9
FOR SAFE OPERATION ........................................................................... 10-13
WHAT'S IN THE BOX ................................................................................ 14-15

BEFORE USING THE BRUSH CUTTER

............................................. 16-17

ASSEMBLY

.......................................................................................................... 18-23

INSTALLING 3 TOOTH BLADE

.............................................................. 24-26

INSTALLING SPOOL

.................................................................................... 28-29

WEARING THE HARNESS

........................................................................ 30-32

STARTING THE ENGINE

....................................................

..........................

34-37

STOPPING THE ENGINE ................................................................................

38

OPEN & REPLACE SPOOL LINE ..................................................... 40-43
ADJUSTING THROTTLE CABLE & IDLING S

PEED .............

44

OPERATION

....................................................................................................... 46-49

TROUBLESHOOTING ............................................................................... 50-53
MAINTENANCE & CARE ....................................................................... 54-56
SPECIFICATIONS ......................................................................................... 57
GUARANTEE ................................................................................................... 58
DECLARATION OF CONFORMITY ................................................. 59

«
1
2
3
4
...
»

Содержание PGBC-5200
































Отзывы:

Нет отзывов