manualshive.com logo in svg

Parker 514C, Руководство по эксплуатации продукта

Поделиться
Скачать
Parker 514C Скачать руководство пользователя страница 35

Diagnostics and Fault Finding

   5-2

 

514C Product Manual

 

DRIVE TRIPS 

When a fault occurs the drive will trip and display the cause of the trip on the indicator LEDs 

or on the diagnostic (test point 6) for the Thermistor/Microtherm Trip.    
The Stall Trip (LED2 on) and the Thermistor/Microtherm Trip are reset by re-applying the 

run signal to Terminal 5.  The drive will then re-start.  (It is necessary to remove then re-apply 

the run signal). 
An Overcurrent (LED3 on) is not reset by the Run signal re-application as this trip can 

indicate that a major fault has occurred.  The overcurrent trip is reset by removing then re-

applying the auxiliary supply.  Remove the Run signal before removing the auxiliary supply.   
Resetting the Stall Trip does not reset the drive’s internal timer that caused the trip.  If the 

drive is operated in current limit (LED5 illuminated) immediately after a Stall Trip the trip 

could re-occur.  This protects the drive and the motor from continuous overload operation.  

However, it is possible to prevent the stall trip by using the Stall Override (Terminal 15). 

DIAGNOSTIC TEST POINT DESCRIPTIONS 

Test 

Node 

Description 

Condition 

Voltage 

1 

In15V Supply 

Auxiliary Supply On 

+15V ±0.15V 

2 

Ex10V Supply 

Auxiliary Supply On 

+10V ±0.025V 

3 

External -10V Supply 

Auxiliary Supply On 

-10V ±0.025V 

4 

Internal -15V Supply 

Auxiliary Supply On 

-15V ±0.15V 

5 

Drive Enable 

Enable  

+10V to +24V 

 

Terminal T20  

Inhibit   

0V 

6 

Motor Microtherm 

Normal  

+12V to +15V 

 

/Thermistor 

Overtemperature  

0V to 2V 

7 

At Zero Setpoint 

At Zero Setpoint  

+13V

2V 

 

 

Above Zero Setpoint   0V 

8 

At Zero Speed 

At Zero Speed  

+13V

2V  

 

 

Above Zero Speed  

0V 

9 

Run 

Run  

+24V

4V 

 

Terminal T5 

Inhibit  

0V 

10 

Health 

Healthy   

+24V

4V 

 

Terminal T19 

Unhealthy   

0V 

11 

Setpoint Ramp Input 

100% Forward Speed  +10V 

 

Terminal T13 

Zero Speed 

0V 

 

 

100% Reverse Speed  -10V 

12 

Positive Trim Setpoint 

100% Forward Speed  +10V 

 

Terminal T10 

Zero Speed 

0V 

 

 

100% Reverse Speed  -10V 

13 

Inverted Setpoint Sum 

100% Forward Speed  -10V 

 

Terminal T21 

Zero Speed 

0V 

 

 

100% Reverse Speed  +10V 

14 

Negative Trim Setpoint  100% Forward Speed  -10V 

 

Terminal T17 

Zero Speed 

0V 

 

 

100% Reverse Speed  +10V 

 

Содержание 514C












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды