background image

   

Cont.1

 

 

 

 

 

  8902/E1 

Sin/Cos Speed Feedback 
Option

 

 

 

  Technical Manual 
 

HA469252U001  Issue 2

 

  Compatible with Version 1.x Software 

 

 

 Copyright 2007 Parker SSD Drives, a division of Parker Hannifin Ltd. 

All rights strictly reserved. No part of this document may be stored in a retrieval system, or transmitted in any 
form or by any means to persons not employed by a Parker SSD Drives company without written permission 
from Parker SSD Drives, a division of Parker Hannifin Ltd . Although every effort has been taken to ensure the 
accuracy of this document it may be necessary, without notice, to make amendments or correct omissions. 
Parker SSD Drives cannot accept responsibility for damage, injury, or expenses resulting therefrom.

 

WARRANTY 

Parker SSD Drives warrants the goods against defects in design, materials and workmanship for the period of 12 

months from the date of delivery on the terms detailed in Parker SSD Drives Standard Conditions of Sale 

IA058393C. 

 

Parker SSD Drives reserves the right to change the content and product specification without notice.

 

Содержание 8902/E1 Series












Отзывы: