BRAKE PADS
Check and/or replace the engine brake pads in service agent regularly, only original parts can be
used as replacement.
9. LUBRICATION INSTRUCIONS
CAUTION: DISCONNECT SPARK PLUG BEFORE SERVICING.
1. WHEELS-Lubricate the ball bearings in each wheel at least once a season with a light oil.
2. ENGINE-Follow engine manual for lubrication instructions.
10. CLEANING
CAUTION: Do not hose engine. Water can damage engine or contaminate the fuel system.
1. Wipe deck with dry cloth.
2. Hose under deck by tilting the mower so that the spark plug is up.
10.1 ENGINE AIR CLEANER
CAUTION: Do not allow dirt or dust to clog the air filter foam element. The engine air cleaner
element must be serviced (cleaned) after 25 hours normal mowing. The foam element must be
serviced regularly if the mower is used in dry dusty conditions.
To CLEAN AIR FILTER
1. Press down the two tabs on top of the filter cover. (Fig.11)
2. Remove cover.
3. Wash filter element in soap water. DO NOT USE GASOLINE!
4. Air dry filter element.
5. Place a few drops of SAE30 oil on the foam filter and squeeze tightly to remove any excess oil.
6. Reinstall filter.
Fig. 11
NOTE: Replace filter if frayed, torn, damaged or unable to be cleaned.
10.2 CUTTING BLADE
CAUTION: Be sure to disconnect and ground the spark plug wire before working on the
cutting blade to prevent accidental engine starting. Protect hands by using heavy gloves or a rag to
grasp the cutting blades .Tip mower as specified in separate engine manual. Remove the hex bolt
and washer which hold the blade and blade adapter to the engine crankshaft. Remove the blade
and adapter from the crankshaft.
WARNING: Periodically inspect the blade adapter for cracks, especially if you strike a foreign
object. Replace when necessary.
For best results your blade should be sharp. The blade may be resharpened by removing it and
either grinding or filing the cutting edge keeping as close to the original bevel as possible. It is
extremely important that each cutting edge receives an equal amount of grinding to prevent an
unbalanced blade. Improper blade balance will result in excessive vibration causing eventual
damage to the engine and mower. Be sure to carefully balance blade after sharpening. The blade
can be tested for balance by balancing it on a round shaft screwdriver. Remove metal from the
heavy side until it balances evenly.
Before reassembling the blade and the blade adapter to the unit, lubricate the engine crankshaft
and the inner surface of the blade adapter with light oil. Install the blade adapter on the crankshaft
with the "star" away from the engine. Refer to Fig.12. Place the blade with the part number
facing away from the adapter. Align the washer over the blade and insert the hex bolt. Tighten the
hex bolt to the torque listed below:
Fig.12
10.3 BLADE MOUNTING TORQUE
Center Bolt 40Nm-50Nm, to insure safe operation of your unit. ALL nuts and bolts must be checked
periodically for correct tightness.
After prolonged use, especially in sandy soil conditions, the blade will become worn and lose some
of the original shape. Cutting efficiently will be reduced and the blade should be replaced. Replace
with an approved factory replacement blade only. Possible damage resulting from blade unbalance
condition is not the responsibility of the manufacturer.
When you change the blade, Must use the original type marked on the blade (for order the blade,
pls. contact your place of purchase).
10.4 ENGINE
Refer to the separate engine manual for engine maintenance instructions.
Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and
follow instructions carefully.
Service air cleaner as per separate engine manual under normal conditions.
Clean every few hours under extremely dusty conditions. Poor engine performance and flooding
usually indicates that the air cleaner should be serviced.
To service the air cleaner, refer to the separate engine manual packed with your unit.
The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is
recommended at the start of each mowing season; check engine manual for correct plug type and
gap specifications.
Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area)
clean to permit proper air circulation which is essential to engine performance and life. Be certain
to remove all grass, dirt and combustible debris from muffler area.
11. STORAGE INSTRUCTIONS (OFF SEASON)
The following steps should be taken to prepare lawn mower for storage.
1. Empty the tank after the last mowing of the season.
a)Empty the petrol tank with a suction pump.
12
11
Содержание 9696093
Страница 1: ...9696093 9696093 Silvan Silvan Silvan...
