3
WEAR an approved hearing protection device to limit noise
exposure as required by Occupational Health and Safety regulations
suitable for machine noise Ievels.
PROTECTIVE CLOTHING
ALWAYS wear approved hearing protection, protective goggles and
a dust mask when working in a dusty environment.
Protective clothing, anti-vibration gloves, safety footwear must be
worn especially when working with hot mix bitumen. Wear sun
cream and wide brimmed hat in exposed areas. Drink plenty of
water.
! ADDITIONAL HAZARDS
Vibration hazard can cause permanent injury SliplTrip/Fall is a major
cause of serious injury or death.
Beware of uneven or slippery work surfaces.
Exercise care when working in the vicinity of unprotected holes
elevated platforms or excavations.
OPERATION
The machine is best suited to the compaction of bituminous and
granular materials e.g. granular soils, gravels and sands or mixtures
of both, Cohesive soils such as silt and clay are best compacted
using the impact force produced by a vibrating rammer.
Where possible the site should be graded and levelled before
commencing compaction.
Correct moisture content in soil is vital to proper compaction.
Water acts as a lubricant to help slide soil particles together.
Too little moisture means inadequate compaction; too much
moisture leaves water’filled voids that weaken the soil’s loadbearing
ability. Compaction of dry materials will be facilitated by moistening
with a water hose fitted with a sprinkler.
Excessive watering or water content will cause the machine to stall.
The optional water tank kit is recommended when the machine is
used on bituminous surfaces as the water film prevents a build-up
of material on the underside of the plate.
Use unleaded grade petrol and ensure that the fuel is free from
contamination.
The vibratory motion provides a self-propelling action.
Position the handle at the opposite end of the machine to the
vibrator.
Start the motor using the recoil starter. (If the motor is fitted with an
on/off switch this must first be turned to ON before starting.)
For more information on starting and correct operating procedures
of the motor, refer to the motor operation manual supplied with the
unit.
Increase the motor speed to the maximum setting using the hand
throttle lever, before commencing compacting.
The machine should be controlled by grasping the handle with both
hands and applying restraint to control the forward motion,
Steer the machine by moving the handle sideways to the right or
left. Ensure other persons and children are clear of barricaded area.
Keep clear of electrical leads and hoses on floor.
ALWAYS maintain good footing so that you do not slip and loose
control when starting or operating the machine.
If the optional water tank is fitted, the flow rate can be controlled by
adjusting the cock in the supply hose to the sprinkler bar.
CARE AND PREVENTIVE MAINTENANCE
Check the oil level in the motor crankcase daily.
Inspect the rubber anti vibration mounts for wear or deterioration.
If the optional water tank is fitted inspect the water hose and its
connections to ensure that they do not leak.
Clean the underside of the plate regularly to prevent a build-up of
material.
SERVICE
Change the oil in the motor crankcase regularly to minimise wear.
Inspect, clean and/or replace the motor air cleaner regularly,
particularly when operating in a dusty environment.
Inspect, clean and/or replace the spark plug regularly.
Check all fasteners for tightness as the machine is subject to
vibration.
Check vee belt tension, wear and that it is running true, adjust or
replace as required.
Product & Performance Specifications
Forward Plate Compactor
Model Number
FCP-87B
Operating Weight (kg)
87
Plate Size (WxL) (mm)
460 x 610
Centrifugal Force Max (kN)
19.8
Vibration Frequency (vpm)
7000
Max Travel Speed (m/min)
26
Max Gradeability (%)
35
Max Compacted Area (m2/h)
717
Lifting Hook
Yes
Engine Make
Honda
Engine Model
GX160
Max Rated Power (Hp)
5.5
Fuel Type
Petrol
Product Code
FT201806-UNIT
Barcode
9300611599513
