background image

 

Unpacking your 

 

Zdac & Placement Guidelines

 

 

Unpacking Your Zdac 

Carefully remove your Zdac from its shipping carton and locate its AC power cord and USB cable.  
While you are unpacking your Zdac, inspect it thoroughly for possible shipping damage and tell your 
Parasound dealer immediately if you find any. If possible, save and store both the inner and outer 
cartons and

–most especially–the foam packing inserts, to protect the Zdac if you have to move it or ship 

it. This would be a good time to make a copy of your sales receipt to store with the Zdac

’s original 

packing. 
 

Again: Do not throw away the Zdac carton or foam packing inserts. 

 

Placement Guidelines 

Install your Zdac away from heat sources such as heating ducts, radiators, or other 
heat-producing components. Always position the Zdac horizontally. Observe the following 
ventilation guidelines when installing the Zdac in an equipment rack or any other enclosed 
space: 
 
You should never install the Zdac in an unventilated equipment cabinet or compartment because hot air 
will not exhaust adequately to prevent overheating. Air won’t often circulate adequately in a cabinet or 
enclosure whose front and back sides are open; pockets of intense heat can still develop around any 
heat-producing equipment. Allow a few inches of empty space on each side and above the unit and try 
to avoid crowding or stacking the Zdac tightly between other components. A ventilation fan is also 
recommended where other heat-producing equipment must be mounted close to the Zdac. 
 
If 

you’re installing the Zdac yourself, use input and output cables that are long enough to 

leave at least two feet of slack; that will enable you to pull the Zdac out of a cabinet to check 
or to change connections without inadvertently disconnecting cables. 

If you’re putting the 

Zdac inside a cabinet, it needs a space that’s at least 11 inches wide so you’ll be able to 
turn it around for access to its rear panel connections. 
 

Rack Mounting Your Parasound Zdac (black Zdac only)   

The Zdac occupies only half the width of a single rack space in a standard 19" equipment 
rack. For rack mounting, you can fasten it to another Parasound Z model by using the Parasound 
SBS (Side-by-Side) mounting kit (sold separately). You can also mount a single Zdac in the 
rack with the accessory Zblank panel extender. The SBS includes four rack mount bolts plus four 
pairs of plastic “shoulder washers.” The washers are important because they insulate the 
Zdac front panel (and chassis) from the metal equipment rack and from the four mounting 
bolts. Place these washers on both sides of the front panel before the mounting bolts are screwed 
into the rack rail. 
 

Note: Only black Zdacs can be rack mounted.  Silver Zdacs cannot be rack mounted.

 

 
 

 

 

 

Note:

 Tighten each bolt just enough to keep the unit secure in the rack to avoid deforming the 

shoulder washers.  Eliminating metal-to-metal contact reduces the likelihood of creating a ground loop 
that might introduce hum into your system. 

 

 

 

Содержание Zdac















Отзывы: