background image

REAR PANEL CONNECTIONS AND CONTROLS continued

8

Note: 

If the controller’s trigger output is a + and - terminal, you can cut the 2.5mm plug off one 

end of the included trigger wire and attach the bare wires to these terminals. The lead with 
the white stripe on it corresponds to the plug’s tip and the unmarked lead corresponds to the 
sleeve of the plug.

Note: 

If the trigger voltage source is DC, the trigger plug tip must be + (positive) and its 

sleeve - (negative). 

12V Out Jack

The Trigger Out jack lets you loop or “daisy-chain” the incoming trigger voltage to an additional 
Model 2125 or other component.

Note: 

The Model 2125 trigger circuit draws a negligible 15 mA from the controller. The total load 

on your controller’s trigger output(s) is the sum of the trigger current drawn by each of the com-
ponents you’ve looped together. Controllers can typically supply 150 mA at their trigger outputs.

Audio Trigger Sens (Sensitivity) Knob

The Auto Turn On Audio Sensitivity knob adjusts the incoming audio level or the “threshold” 
required to turn on the Model 2125. Its 12 o’clock position will be suitable in most cases. To 
increase sensitivity for response to lower level audio signals, turn the knob counter-clockwise 
.
Turn the knob clockwise toward - to decrease its sensitivity. This will prevent spurious noise 
and switching transients in your system from false-triggering the Model 2125.

Note: 

Plugging in the 2125’s AC cord for the first time will usually create an internal power 

surge that “false triggers” its Audio auto turn on, even if there’s no audio signal at its input 
jacks, and it will remain on for 10-15 minutes after you switch it off. This is normal.

Ground Switch

Ground is the normal position for this switch. If you hear background hum in the speakers 
connected to the Model 2125, try setting the Ground Lift Switch to its Lift position. The Ground 
Switch disconnects or “lifts” the audio circuit ground from the chassis ground. This often helps 
to eliminate audible hum that results from ground loops. Ground loops are multiple ground 
paths such as the metal-to-metal contact with the panels or chassis of other components 
combined with the ground connections of the audio cables or even the ground wires of the 
various AC cords.

AC Power Connections and AC Grounding

If possible, plug your Model 2125 into the same AC outlet that your accompanying audio com-
ponents (especially then preamp or system controller) are plugged into. The ground potential 
between different AC outlets may be higher or lower, resulting in audible hum.

             CAUTION

To Prevent Electric Shock, Do Not
Remove Cover. No User-Serviceable
Parts Inside. Refer Servicing To
Qualified Service Personnel.

              WARNING 

To Prevent Fire Or Shock Hazard,
Do Not Expose This Unit To Rain
Or Moisture.

2125 Two Channel Amplifier

Parasound Products, Inc.

San Francisco, CA    U S A

THX and Ultra2 are trademarks of THX Ltd.
which may be registered in some jurisdictions.
All right reserved.

Speaker Pair A

L

R

Mono

Manual

Audio Sens

Max Min

12V Trigger

Ground

Lift Norm

Mono

Stereo

4-8

Ohms

2-3 

Ohms

230V

50Hz

115V

60Hz

20Hz 40Hz

Flat

Audio

Auto Turn On

Loop

Level

Bridging

Input

12V

In

Loop

R

Mono

THX

THX

AC      115V/60Hz

AC      230V/50Hz

Power Consumption: 550W

AC

Voltage

Load

Impedance

L

High Pass Filter

Speaker Pair B

L

R

Mono

             CAUTION

To Prevent Electric Shock, Do Not
Remove Cover. No User-Serviceable
Parts Inside. Refer Servicing To
Qualified Service Personnel.

              WARNING 

To Prevent Fire Or Shock Hazard,
Do Not Expose This Unit To Rain
Or Moisture.

2125 Two Channel Amplifier

Parasound Products, Inc.

San Francisco, CA    U S A

THX and Ultra2 are trademarks of THX Ltd.
which may be registered in some jurisdictions.
All right reserved.

Speaker Pair A

L

R

Mono

Manual

Audio Sens

Max Min

12V Trigger

Ground

Lift Norm

Mono

Stereo

4-8

Ohms

2-3 

Ohms

230V

50Hz

115V

60Hz

20Hz 40Hz

Flat

Audio

Auto Turn On

Loop

Level

Bridging

Input

12V

In

Loop

R

Mono

THX

THX

AC      115V/60Hz

AC      230V/50Hz

Power Consumption: 550W

AC

Voltage

Load

Impedance

L

High Pass Filter

Speaker Pair B

L

R

Mono

Содержание NewClassic Model 2125

















Отзывы: