background image

SERVICING YOUR P 3

If All Else Fails –Call Us for Help

Call your Parasound dealer or Parasound’s Technical Service Department toll free at 
1-866-770-TECH (8324). We can often solve the problem with simple diagnostic tests you can
perform yourself. If we determine that your P 3 will need further inspection or servicing, we will:

a) refer you to an authorized Parasound repair center near you, or 
b) authorize return of the unit to us and advise you of the correct procedure.

Procedure for Returning Your P 3 to Parasound for Service

If Parasound determines that you should send your P 3 to Parasound, you will be given a Return
Authorization (RA) number. This RA number must be clearly marked on the 

outer carton only. 

IMPORTANT: Enclose a copy of your original purchase receipt. A unit is eligible for warranty
repair ONLY when the purchase receipt shows that the unit was purchased from an Authorized
Parasound Dealer. A unit obtained through unauthorized channels is not eligible for warranty
repair. Parasound is not responsible for any sellers’ misrepresentations about our warranties or
other service policies.  

We do not accept any of the following: 

Units with collect shipping charges
Units without a valid RA number 
Units without a suitable shipping carton
Units for which we see or hear evidence of improper packing

For a non-warranty repair, contact us for an estimate of the repair charges before you ship the
unit to us. The same packing and Return Authorization number procedures apply.

Important Notice - Shipping the P 3

Before shipping the unit to Parasound, you MUST re-pack the unit into its fitted molded foam
insert sandwich and its original carton. If you do not have the original packing cartons and foam
inserts, call us for new packing materials that we can provide to you for a nominal charge. Use of
any other carton and packing materials will probably result in shipping damage, and refusal of
the unit. Common carriers such as UPS seldom pay claims for damage incurred during shipment
when a product is surrounded only with Styrofoam “peanuts” or otherwise improperly packed. 

We  cannot stress enough the importance of properly packing your P 3. Shipping damage
resulting from inadequate packing can cost you a lot of money and significantly increase the
time required for repair. 

Ship the unit with adequate insurance. After repair under warranty, the unit will be returned to
you via prepaid UPS within the continental United States.

21

Содержание Halo P 3





























Отзывы: