background image

17

Turn On Options

For your convenience, there are three ways the Halo Integrated can be
turned on and off:

Manual -

Press the On-Off button on the front panel or use the On and Off buttons on

the remote control.

Automatic (12 V) -

When 12 volts is applied to the 12 V Input jack the Halo Integrated
will automatically power on.

Always On (AC) -

Whenever the Halo Integrated’s AC power cord is plugged into a

live outlet it will be powered on.

Note:

When either automatic turn on option is selected the front panel On-Off

button is disabled so that power on/off is controlled solely by the triggering device
or live AC power.

Turn On Options Switch:

Manual Position

When the Turn On Options switch is in its Manual position, the Halo Integrated must be
turned on and off manually by pressing the front panel On-Off button or by using the
remote control’s On and Off buttons.

12 V Position (Automatic On/Off)

When the Turn On Options switch is set to its 12 V position, the Halo Integrated is
automatically powered on only when an ex9 to +12 volts is present at its 12 V input
jack. When the external voltage ceases the Halo Integrated will turn off immediately. The 12 V
switch position disables the front panel On-Off button and the remote control’s On and Off
buttons.

AC (Always On)

The Halo Integrated will turn on automatically when the AC mains electrical outlet it’s plugged
into is live.

Note:

The Halo Integrated will turn off only when the AC mains outlet is switched

off. Pressing the On-Off button on the front panel or the On and Off buttons on the remote
control will not turn it off when AC (Always On) is selected.

Note: Whenever the Auto Turn On switch is set to 12 V or AC the On-Off button on the front
panel and the remote control’s On and Off buttons are disabled.

3.5 mm Mini Jack and 2.5 mm Sub-Mini Jacks

Some models of Parasound power amplifiers and preamplifiers use 2.5 mm “sub-mini” 12 volt
trigger jacks. To connect the Halo Integrated with these models we include a trigger wire with a
3.5 mm plug at one end and a 2.5 mm plug at the other end.

Содержание Halo Integrated



























Отзывы: