Paramount Fitness ME II Скачать руководство пользователя

Страница: 118 / 195

Paramount User Guide

118

P a g e

Mac OS X

Software drivers need

not

be installed to operate the Paramount on the Mac. Plug the USB cable into the

mount and into one of the computer’s USB ports then follow the instructions below to configure

TheSkyX

Professional Edition

for Mac.

Windows

The Software Bisque MKS 5000 USB driver must be installed before the Paramount can be operated by

TheSkyX Professional Edition

for Windows (both 32- and 64-bit Editions). See “Appendix A: Installing the

MKS 5000 USB Windows Driver” on page 170 for step by step installation instructions.

Controlling the Paramount with TheSkyX Professional Edition

After installing the MKS 5000 driver (Windows only), and plugging the USB 2.0 cable into the mount and
computer, you must configure

TheSkyX Professional Edition

to control the

Paramount

Make sure the mount is turned on so that the computer recognizes the Paramount USB port.

The Paramount must be turned on before the operating system will recognize
the built-in USB port on the Electronics Box.

From

TheSkyX Professional Edition

, choose the

Telescope Setup

command from the

Telescope

menu.

On the

Imaging System Setup

window, highlight

Mount

in the

Imaging System

list.

Select the

Choose

command from the

Mount Setup

pop-up menu.

Expand

Software Bisque

, select

Paramount ME II, Paramount MX or Paramount MX+

and click

Choose the

Settings

command from the

Mount Setup

pop-up menu.

On the Mac, the Paramount control system name is “usbmodem” with a
“numerical identifier” (see Figure 68). The numerical identifier in the name
varies depending on which version of Mac OS X is installed.

Figure 68: The Mac Serial Device Settings window.

Содержание ME II



































































































































































































Результаты поиска

Содержание ME II

Отзывы:

Похожие инструкции для ME II

Бренды по названию

Популярные бренды

Paramount Fitness ME II, Руководство пользователя

Результаты поиска

Содержание ME II

Отзывы:

Похожие инструкции для ME II

Бренды по названию

Популярные бренды