Paramount Fitness ME II Скачать руководство пользователя | Manualshive

Страница: 170 / 195

background image

Paramount User Guide

170

|

P a g e

Appendix A: Installing the MKS 5000 USB Windows Driver

When used with the Windows operating system, the Paramount MKS 5000 control system requires a one-
time software driver installation before

TheSkyX Professional Edition

for Windows can be used to control

the mount.

Windows USB Driver Installation and Use

The following procedure describes how to install the MKS 5000 USB driver under Windows 8, Windows 7
and Windows XP (32-bit and 64-bit editions) and configure

TheSkyX Professional Edition

to use this port

once the driver has been installed.

1.

From Windows Explorer, double-click the file named

MKS 5000 Driver Installer.exe

located in the

MKS 5000 Driver

folder on

TheSkyX Professional Edition

for Windows DVD you received with your

mount.

This installer can also can be downloaded from the Software Bisque web site from the following
URL:

http://www.bisque.com/MKS5000

Remember, you must sign in and

register your Paramount

serial number

at

www.bisque.com/register

before your Software Bisque account can download

this file.

2.

Follow the installation instructions to complete the installation.

3.

Once driver installation is complete, plug the USB 2.0 cable into the USB port on the Electronics
Box and the USB 2.0 connector into a free USB port on the computer.

The Paramount must be turned on before the operating system will recognize the USB port on
the Electronics Box and load the MKS 5000 driver.

4.

Flip the Paramount power switch to the on position.

5.

From

TheSkyX Professional Edition’s

mount

Settings

window, select the COM port on the

Telescope > Telescope Setup > Mount Setup pop-up > Settings > Serial Port

list with the

description

Software Bisque MKS 5000

«
...
168
169
170
171
172
...
»

Содержание ME II




































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ME II

Discovery expedition Travel Scope 60

Бренд: Celestron Страницы: 4

Cometron CO-114

Бренд: Celestron Страницы: 20

Skyline PRO 105 MAK

Бренд: Levenhuk Страницы: 60

8442 - Omega Muzzleloader Scope 1.65-5x36

Бренд: Nikon Страницы: 1

Бренд: SitePro Страницы: 12

Ritchey-Chretien 8266

Бренд: Orion Страницы: 12

Бренд: Kowa Страницы: 5

CORONADO SolarMax II series

Бренд: Coronado Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды