background image

PAGE 6

OPERATION MANUAL V1.0

Adjusting Squelch Level

Since increasing the squelch level will also reduce the reception distance, it’s recommended to choose the lowest level 
that can eliminate the interference.

If this still does not solve the problem it means this frequency is not suitable. Adjust the squelch back to its preset level 
and use the scan function to locate a clear, interference-free channel.

When interference is encountered try reducing the sensitivity of the receiver, thus making it less susceptible 
to interference.

1. 

Press and release 

SET

 button until the SQUELCH SETUP page appears.

2. 

Press 

p

(UP) or 

q

(DOWN) button to choose a new level between 1 and 10. 

5 seconds after selecting a level, it will be automatically saved.

Receiver Installation

For best operation, the receiver should be at least 1m above the ground and 1m away 
from a wall or metal surface to minimise reflections. The transmitter should also be 
at least 1m away from a wall or metal surface to minimise reflections. The transmitter 
should also be at least 1m away from the receiver. Keep antennas away from noise 
source such as motors, automobiles, neon light and large metal objects.

SQUELCH SETUP

LEVEL:01

SQUELCH SETUP

LEVEL:03

Rack Mounting

The receiver can be cabinet-mounted by either one or two units. If only one receiver is to be mounted, an optional kit is 
available and it’s installed as shown in Fig 1. If two receivers are to be mounted, they can be assembled by another kit and 
installed as shown in Fig 2.

Содержание Stage-100 Series













Отзывы: