manualshive.com logo in svg

Paradyne Hotwire 8775, Руководство по установке, Страница: 2 / 26

Поделиться
Скачать
Paradyne Hotwire 8775 Скачать руководство пользователя страница 2

 2

8775-A2-GZ40-10

March 1999

Installation Overview

Installation and configuration of the Hotwire 8775 Termination Unit consists of:

H

Installing the Termination Unit in the DSLAM.

H

Connecting to the DTE.

H

Connecting to an MDF.

H

Providing initial unit identity information or changing existing identity
information.

H

Configuring your unit using the Configuration Edit menus.

Before you install the Hotwire 8775 Termination Unit, read the 

Important Safety

Instructions on page 23.

Be sure to register your warranty at www.paradyne.com. Select 

Service &

Support 

→

 Warranty Registration.

Tool Required

-

Small- to medium-size flat-blade screwdriver.

Planning the 8775 Termination Unit Installation

Review the following list to help plan for the installation.

-

Obtain the applicable cables; refer to 

Cables You Need on page 3.

-

Make sure the Hotwire DSLAM chassis is installed and power is supplied to
the chassis.

-

After the 8775 Termination Unit is installed, there are configuration
procedures that must be performed before you can begin to use the 8775
Termination Unit. Refer to the User’s Guide for more detailed configuration
procedures.

Содержание Hotwire 8775



























Отзывы:

Нет отзывов