manualshive.com logo in svg

Paradyne Hotwire 8775, Руководство по установке, Страница: 18 / 26

Поделиться
Скачать
Paradyne Hotwire 8775 Скачать руководство пользователя страница 18

 18

8775-A2-GZ40-10

March 1999

Table 2.

Synchronous Data Port Options (2 of 2)

Port (DTE) Initiated Loopbacks

Possible Settings: Disable, DTLB, DCLB, Both
Default Setting: Disable

Allows the initiation and termination of a local Data Terminal Loopback (DTLB) or
remote Data Channel Loopback (DCLB) by the DTE connected to this port. (DTLB is
equivalent to a V.54 loop 3, and DCLB is equivalent to a V.54 loop 2.) Control of these
loopbacks is through the DTE interchange circuits as specified by the V.54 standard.

Table 3.

Copy Ports Options

From: Port

Possible Settings: 1, 2, 3, 4
Default Setting: 1

Controls the source of the configuration options.

To: Port

Possible Settings: 1, 2, 3, 4, All
Default Setting: 2

Controls the target of the configuration options.

NOTE:

Peer IP Address and Circuit Identifier are 

not copied.

Table 4.

System Options

DSL Mode

Possible Settings: LTU, NTU
Default Setting: LTU

Controls whether the unit is configured as a control unit or tributary unit.

NOTE:

Changing this option will reset the card.

Test Timeout

Possible Settings: Enable, Disable
Default Setting: Enable

Allows user-initiated tests to end automatically. The feature should be enabled when the
unit is remotely managed, so that control can be regained after a test is accidentally
executed.

NOTE:

Tests commanded by the DTE or network-initiated tests are not affected by
this test timeout.

Test Duration (min)

Possible Settings: 1–120
Default Setting: 10

Number of minutes for a test to be active before automatically ending.

Test Duration (min) option appears when Test Timeout is enabled.

Содержание Hotwire 8775



























Отзывы:

Нет отзывов