Paradyne FrameSaver SLV 9580 T3 ATM DSU Скачать руководство пользователя

Страница: 1 / 18

9580-A2-GZ40-10

June 1999

FrameSaver

SLV 9580 T3 ATM DSU

Installation Instructions

Document Number 9580-A2-GZ40-10

June 1999

Installation Checklist

Installation of the FrameSaver SLV 9580 DSU requires the following steps:

Verify the contents of the shipping carton

Mount the DSU in a cabinet or on open rails

Connect the DSU to a power source

Monitor the power-up self-test

Connect the DSU to its DS3 interface

Connect the DSU to its DTEs

Connect the DSU to an Ethernet interface

Connect the DSU to a terminal or PC, directly or through a modem

Enter a device profile

Set up system Login IDs and access levels

Configure the system

— Configure management PVCs and any other unique PVCs

— Enter and configure VPI/VCIs if your switch does not support traffic

descriptors

— Configure and run Auto-Configuration

Connect the DSU to its monitor and NetScout Probe, if used

Test the system

At any step, diagnose and correct any errors.

Physical installation is described in this document. For detailed configuration and
troubleshooting information, see the

FrameSaver SLV 9580 T3 ATM DSU User’s

Guide (9580-A2-GB20).

Содержание FrameSaver SLV 9580 T3 ATM DSU



















Результаты поиска

Содержание FrameSaver SLV 9580 T3 ATM DSU

Отзывы:

Похожие инструкции для FrameSaver SLV 9580 T3 ATM DSU

Бренды по названию

Популярные бренды

Paradyne FrameSaver SLV 9580 T3 ATM DSU, Руководство по установке

Результаты поиска

Содержание FrameSaver SLV 9580 T3 ATM DSU

Отзывы:

Похожие инструкции для FrameSaver SLV 9580 T3 ATM DSU

Бренды по названию

Популярные бренды