manualshive.com logo in svg

Paradyne 8922, Инструкция по установке и эксплуатации

Поделиться
Скачать
Paradyne 8922 Скачать руководство пользователя страница 9

9

Cabling

The POTS card normally is connected to a 66 Block using a straight-through cable with 
two RJ21X plugs. The cable you need depends on the hardware configuration of the 
66 Block or other connection point. See 

Table 3, RJ21X Connector Pinouts, on page 19

.

Attach the cable to the 50-pin Telco jack on the back of the DSLAM that is associated 
with the slot the POTS card resides in.

Fastening the Cable with Cable Ties

Procedure

To fasten the Telco connector to the  chassis using the provided cable ties:

1.

Replace the longer captive screw on the cable connector with the #4-40 Phillips 
pan-head screw shipped in a plastic bag with the BAC chassis. 

2.

Locate the connector on the back of the chassis that corresponds with the slot 
where you installed the POTS card. Connectors are labeled 1–3 on the 8620 
chassis, and 1–18 on the 8820 chassis. 

3.

Plug the Telco 50-pin cable into the appropriate connector.

4.

Thread the provided cable tie through the anchor mount on the end of the connector 
where the cable will lie. Tighten the cable tie around the connector and cut off any 
excess.

5.

Secure the other end of the Telco 50-pin cable by tightening the captive pan-head 
screw.

01-16900

Anchor

Mount

Telco 50-Pin

Connector

Cable

Tie

Replaced with

Supplied #4-40

Phillips Pan-head

Screw

Содержание 8922

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды