DigiplexNE DGP-NE96
- 40 -
Programming Guide
Other Settings and Modes
PARADOX MEMORY CARD (PMC-3)
[3966]
__/__ Phone Number 2 Fail to Communicate
[3978]
Future Use
[3967]
__/__ Phone Number 3 Fail to Communicate
[3979]
Future Use
[3968]
__/__ Phone Number 4 Fail to Communicate
[3980]
__/__ Bus Fault Restore
[3969]
Future Use
[3981]
__/__ Module Tamper Restore
[3982]
__/__ ROM Check Error Restore
TROUBLE RESTORE REPORT CODES
[3983]
__/__ Module TLM Restore
Section
Report Code
[3984]
__/__ Module Failure to Communicate Restore
[3970]
__/__ TLM1 Restore
[3985]
__/__ Printer Fault Restore
[3971]
__/__ AC Failure Restore
[3986]
__/__ Module AC Failure Restore
[3972]
__/__ Battery Failure Restore
[3987]
__/__ Module Battery Failure Restore
[3973]
__/__ Auxiliary Supply Restore
[3988]
__/__ Module Auxiliary Failure Restore
[3974]
__/__ Bell Output (Reconnected or Restored)
[3989]
Future Use
[3975]
__/__ Clock Loss Restore
[3990]
__/__ Wireless Transmitter Battery Low Restore
[3976]
__/__ Fire Loop Trouble Restore
[3991]
__/__ Wireless Transmitter Supervision Trouble Restore
[3977]
Future Use
Section
Description
[4000]
Display Serial Number of Control Panel and All Modules Connected to the Communication Bus:
After entering section
[4000]
, the keypad will display the 8-digit serial number of the control panel. Use the [ ] and [ ] keys to scroll
through the serial number of each module connected to the communication bus.
[4001]
Module Reset:
Reset a module’s programmed contents to default by entering its serial number.
[4002]
Locate/Unlocate Module:
Locate a specific module (e.g. detector, zone expander, etc.) connected to the communication bus by entering the module's serial number.
The green “
LOCATE
” LED on the module will begin to flash until the serial number is re-entered or the appropriate “tamper” or “unlocate”
switch on the module is pressed.
[4003]
Module Programming Mode:
Enter the serial number of the module you wish to program.
[4004]
Module Broadcast:
Copy the contents of all programming sections from one module to one or more modules of the same type. Enter the serial number of the
source module, followed by the serial numbers of the modules you wish to program and press
[
ACC
]
to begin transfer.
Label Broadcast:
Copy user, door and partition labels from the control panel to all keypads and printer modules connected to the communication bus. To
transmit the labels, in section [4004], enter the control panel’s serial number. From the Destination screen, do not enter a serial number,
press the
[
ACC
]
button.
PLEASE NOTE: The Module and Label Broadcast feature will only work when a module is broadcasting its data to a module or to
modules of the same type and model number. For example, an APR-PRT1 (Printer Module) cannot broadcast to an APR3-PRT1.
Likewise, a DGP module cannot broadcast to a DGP2 module.
[4005]
Remove Modules:
After entering the section, the control panel will scan all modules connected to the communication bus. If any missing modules are
detected (i.e. detector removed from the communication bus), the control panel will erase the module's serial number, removing the
module from the control panel's memory.
[4010]
Download from the
Memory Key
to the control panel
except
sections
[0001]
to
[0096]
and
[0501]
to
[0532]
.
[4011]
Download from the
Memory Key
to control panel
including
sections
[0001]
to
[0096]
and
[0501]
to
[0532]
.
[4020]
Copy the control panel sections to the
Memory Key
except
sections
[0001]
to
[0096]
and
[0501]
to
[0532]
.
[4021]
Copy the control panel sections to the
Memory Key
including
sections
[0001]
to
[0096]
and
[0501]
to
[0532]
.
