Paradox 738ULT, Справочное и монтажное руководство

Страница: 15 / 56

Esprit 728 Ultra & 738 Ultra
11
2.14 Status LED
The green
STATUS
LED is used to show the user what the status of the control panel is.
• If the LED flashes once every second, operation is normal.
• If the LED is ON 1 second and OFF 1 second, there is a trouble in the system.
• If the LED is always ON, the panel is using the phone line.
• If the LED flashes rapidly for 4 seconds after power-up, the installer lock is enabled.
Part 3: Access Codes
3.1 Installer Code
Streamline - Section 00
D
Hex Programming - Addresses 000 to 002
Default: 282828 for 728 Ultra; 383838 for 738 Ultra
Only the Installer code allows you to program all control panel settings, except the Master and user codes. To program any
setting in the control panel you must enter the programming mode by pressing the
[
ENTER
] key followed by the Installer code. The
Installer code contains six digits and each digit can be any value from 0 to 9. Although the control panel can accept 4-digit codes,
when programming the Installer code, always enter six digits. To change the Installer code press:
[
ENTER
] + Installer code + [0] [0] [0] + First 2 [0] [0] [1] + Next 2 [0] [0] [2] + Final 2 [
ENTER
]
3.2 Master and User Codes
Default Master Code: 474747
You cannot use the Installer code to program the Master and user codes. Only the Master code and User code 1 can program
these access codes (see
Programming Master and User Codes on page 40).
3.3 User/Access Code Length
Feature Select Programming
D
Address 088; Key [9]
Default: 6-digit Access Codes
When programming user codes, an option for either 4-digit or 6-digit access codes can be programmed. When the 4-digit option is
selected, entering a 4-digit code will allow the person access. Using the 6-digit option, entering 6 digits is required to allow access.
Key [9] OFF: 6-digit Access codes
Key [9] ON: 4-digit Access codes
[
ENTER
] + Installer code + [0] [8] [8] + [9] ON/OFF + [
ENTER
] twice
3.4 Duress
Feature Select Programming
D
Address 090; Key [0]
Default: Duress Disabled
When unwillingly forced to disarm a system, a user can enter User code #48 instead of their usual code. This code will disarm the
system and send a silent alert (Duress code) to the monitoring station.
Key [0] OFF: Duress Disabled
Key [0] ON: Duress Enabled
[
ENTER
] + Installer code + [0] [9] [0] + [0] ON/OFF + [
ENTER
] twice
3.5 Installer Lock
Decimal Programming
D
Address 058
Default: Address Empty
Program 147 into address 058 to lock all programming. When the installer lock is enabled, the
STATUS
LED will flash rapidly and
the dialer relay will make a clicking noise (made by the relay opening and closing) for 4 seconds during power up. Hence,
performing a hardware reset (see
Power Down Reset on page 39) will not affect the current settings. To remove the installer lock,
enter any value besides 147.
[
ENTER
] + Installer code + [0] [5] [8] + [1] [4] [7] + [
ENTER
]
3.6 Master Code Lock
Feature Select Programming
D
Address 090; Key [
BYP
]
Default: Disabled
This feature locks both the Master code and User code 1. With address 090 key [
BYP
] enabled, the Master code and User code 1
cannot be changed or deleted. With this feature enabled, the Master code and User code 1 can only be changed or deleted
through Espload or by disabling this feature.
[
ENTER
] + Installer code + [0] [9] [0] + [
BYP
] ON/OFF + [
ENTER
]