Pandora DXL 1930L, Руководство пользователя

Страница: 14 / 21

27 26
U S E R M A N U A L P A N D O R A D X L 1 9 2 0 L / 1 9 3 0 L C A R S E R V I C E - S E C U R I T Y S Y S T E M
Level 4 Resetting to factory settings
Level 5 Recording Bluetooth engine compartment module
Level 6, 7 Recording Bluetooth radio relays №1, №2
Level 8 Reserved
Level 9 Reserved
Level 10 Configuring system settings via the wireless interface
Level 11 Programming and configuring “Immobilizer code“
Level 12 Reserved
Level 13, 14 Reserved
Level 15 Emergency disabling of immobilizer radio tag
Level 16 Updating Bluetooth modem firmware
Level 17 Programming bypass of original immobilizer
Level 18 Registering and unregistering mobile device
Level 19, 20 Updating radio relays №1, №2 firmware
Level 1 – Recording remotes and radio tags into the system’s memory
Prepare to record all radio tags (you can record up to 3 tags), install batteries in the radio tags.
Enter programming menu and then press
VALET
button once.
LED
indicator will light green and the
system will enter the tag recording mode. Tags are recorded (paired) one by one, in any order and without time
limit. All previously registered radio tags will be removed when you overwrite new tags or overwrite old tags.
Recording radio tags:
Press control button on a tag and hold it for 6 seconds (6 flashes of tag status indicator), release the
button after the sixth flash. If the recording was successful, a siren will emit 1 beep, after that you can
move to recording the next tag.
Saving changes:
To finish the recording of radio tags into the system,
VALET
button should be pressed once again,
the series of red and green flashes of status LED indicator will confirm the saving.
Level 2 – Changing the factory preset of the service PIN-code
Prepare a new value of the “ Service PIN-code “ , it should consist of 4 digits (from 1 to 9). Write
down or remember the new PIN-code.
Enter programming menu and then press VALET button twice. The system will enter “Changing
Service PIN-code“ mode and the status LED indicator will turn off.
Changing the “ Service PIN-code “ :
• Enter the first digit of the code using
VALET
button. Press the button a number of times, equals
to the first digit. Pauses between presses should not exceed 1 second, every pressing will confirm with
orange LED indicator flash. Pause for more than 1 second and red LED indicator confirms the input of
the first digit. Then you can enter the next digit.
• Enter the other numbers in the same manner. The input of the fourth number will be confirmed
by series of red and green LED indicator flashes. The system will wait for PIN-code re-entering.
• Enter all four digits again;
• If you were able to correctly enter the “Service PIN-code“ twice, the indicator will produce the series
of red and green flashes, new PIN-code will be recorded, the system will return to programming mode. In
case of the incorrect code input the indicator will be lit red, the system will return to programming mode.
Level 3 – Recording the idle speed to the system memory
To timely turn off the starter during automatic or remote engine start via digital or analog
tachometer input and the correct operation of the “ Smart Turbo Timer “ , it is necessary to record
the engine idle speed.
To record idle speed to the non-volatile system memory, enter the programming menu. Press
VALET button three times. Switch on the ignition and start the engine after entering this level of
programming (the engine should be warmed-up, idle speed should match the stable idle speed of the
warmed-up engine). The system will confirm the presence of the idle speed status with green flashes of
LED indicator. Wait until the stable idle speed will be reached and save the changes.
Saving changes:
Press VALET button once to save idle speed. Successful recording of the idle speed will be confirmed
with the series of red and green flashes of
LED
indicator. The system will exit programming menu and
reboot after saving the idle speed.
Level 4 – Resetting to factory settings.
The procedure recovers the factory settings of the system without deleting previously
registered devices (tags, mobile device, relays, etc.) that is stored in the non-volatile memory.
To reset the settings enter the programming mode and press
VALET
button four times. Press and
hold VALET button for more than 4 seconds until siren sound, then release the button. The system will