![background image](http://html.mh-extra.com/html/panasonic/wvnw474s-color-cctv-camera/wvnw474s-color-cctv-camera_operating-instructions-manual_1512023028.webp)
-28-
• The camera will deactivate the detector for a few
minutes after the power of the camera is turned on
or the BW setting in the Special Menu is set to
something other than OFF.
• The motion detection function is not designed
specifically for prevention of theft, fire, etc.
9. Menu/DIP SW Selection
Some of the settings: picture upside down, aperture
level, BW, and synchronization: are operable in the
menu setup or from the DIP switch on the camera. You
can select MENU or DIP SW in the second from the bot-
tom of the **CAM SET UP** menu to apply either set-
tings to the camera.
1. Move the cursor to the second bottom line.
2. Press [Left] or [Right] to select the parameter.
MENU:
Applies the settings specified in the menu
setup.
DIP SW:
Applies the settings specified by the DIP
switch, SW1-SW5.
The default setting is DIP SW.
Note:
The **SPECIAL** menu specifies the follow-
ing: picture upside down, aperture level, and BW
settings: while the **CAM SET UP** menu speci-
fies the synchronization mode.
10. Special Menu (SPECIAL)
This menu lets you adjust and set up the video signal of
the camera to meet your requirements.
Move the cursor to END in the bottom line of the CAM
SET UP menu and press [Left] and [Right] simultane-
ously (holding down [Left] and press [Right]) for 2 sec-
onds or more. The SPECIAL menu appears on the mon-
itor screen.
10-1. Camera Picture Upside Down Positioning
(UP SIDE DOWN)
1. Move the cursor to UP SIDE DOWN.
2. Select ON when you want to turn the picture upside
down.
10-2. Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to CHROMA GAIN.
2. While observing the vectorscope or color video
monitor, move the "I" cursor to adjust the chroma
level.
10-3. Aperture Gain Setting (AP SHARP/AP SOFT)
1. Move the cursor to AP SHARP.
2. To select AP SOFT, press [SET].
3. While observing the waveform monitor or color video
monitor, move the "I" cursor to adjust the aperture
gain level.
10-4. Pedestal Level Setting (PEDESTAL)
1. Move the cursor to PEDESTAL.
2. While observing the waveform monitor or color video
monitor, move the "I" cursor to adjust the pedestal
level (black level).
10-5. Chroma Phase (Hue) Setting (HUE)
1. Move the cursor to HUE.
2. While observing the vectorscope or color video
monitor, move the "I" cursor to adjust the hue (chro-
ma phase) level.
10-6. Electronic Zoom (EL-ZOOM)
1. Move the cursor to EL-ZOOM.
2. Select ON or OFF using [Left] or [Right].
The factory default setting is OFF.
ON:
x2 electronic zoom is available with the ZOOM
switch on the controller.
OFF:
The electronic zoom function is disabled.
3. While the cursor is on EL-ZOOM, press [SET]. The
EL-ZOOM setting menu appears.
4. Move the cursor to PUSH SET for ZOOM and press
[SET] to display the ZOOM setting menu.
** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
MENU
RET END
↵
↵
↵
** SPECIAL **
UP SIDE DOWN OFF
CHROMA GAIN ....I....
AP SHARP ...I.....
PEDESTAL ......I..
HUE ....I....
EL-ZOOM OFF
BW OFF
BURST(BW) ON
CAMERA RESET PUSH SW
RET END
** EL-ZOOM **
PAN/TILT
→
PUSH SET
ZOOM
→
PUSH SET
U TILT D/L PAN R
RET END
** EL-ZOOM **
PAN/TILT
→
PUSH SET
ZOOM
→
PUSH SET
U ZOOM D
RET END
Содержание WVNW474S - COLOR CCTV CAMERA
Страница 67: ......