Panasonic WV-X6511N Скачать руководство пользователя

Страница: 60 / 265

2.3.2.4 Alarm: Configure the details for image transfer or recording
conditions

Set FTP transfer (FTP transfer setup menu)

FTP transfer when an alarm is detected is set in this section.

Refer to page 191 for information about how to set the above screen. For information about “Image
compression rate upon alarm detection” and “Image quality upon alarm detection”, refer to “2.7.4.2 Configure
settings relating to image quality on alarm action”.

[Next] button

If you select “Alarm output” in the alarm setup menu and click the [Next] button, the alarm output setup menu
will be displayed. (

page 62)

If you click the [Next] button in the alarm setup menu without selecting “Alarm output”, the mail setup menu
will be displayed. (

page 63)

Note

•

If you click the [Next] button, the setting items in the screen are saved.

[Back] button

If you click the [Back] button, the alarm function type setup menu will be displayed. (

page 59)

Operating Instructions

2 Settings

Содержание WV-X6511N










































































































































































































































































Результаты поиска

Содержание WV-X6511N

Отзывы:

Похожие инструкции для WV-X6511N

Бренды по названию

Популярные бренды

Panasonic WV-X6511N, Руководство по эксплуатации

Результаты поиска

Содержание WV-X6511N

Отзывы:

Похожие инструкции для WV-X6511N

Бренды по названию

Популярные бренды