8
have deteriorated and it may cause discoloration.
Even when changing the fixed shooting direction after
continuously shooting a spotlight for a certain period,
the discoloration may remain.
Do not aim this product at strong light sources.
A light source such as a spot light causes a blooming
(light bleeding) or a smear (vertical lines).
About the self-diagnosis function
When this product malfunctions due to exogenous
noise, etc. for 30 seconds or more, the product will
automatically reset and will return to normal state. When
the product is reset, initialization will be carried out
as when the power of the product is turned on. When
the product repeatedly resets, exogenous noise level
around the product may be high and that may cause
malfunction. Contact your dealer for instructions.
Lens and pan/tilt head
If a lens and pan/tilt head are not performed for a long
period of time, the grease coating inside these parts
may become sticky. That may obstruct the parts from
moving. To prevent this, move the lens or pan/tilt head
periodically. Or perform position refresh periodically.
About the position refresh function
Noise may be produced or the preset positions may
become inaccurate after a long operation.
Execute the "REFRESH" operation periodically, the
camera position will be corrected, and it is also
recommended to clean the slip ring of the camera.
Refer to the operating instructions (PDF) for further
information.
Consumable parts
The following are consumables: Replace them in
accordance with their lives. Their lives vary depending
on use environment and conditions.
Lens unit, slip ring: Approx. 3.7 million operations
(Lifetime around 20000 hours is just an indication when
using the camera at +35 °C {95 °F}.)
Cooling fan (motor): around 52000 hours
Indication label
Refer to the indication label on the back of sunshield for
the information on equipment classification and power
source, etc.
Blooming
Smear
Bright subject
To keep on using with stable performance
Parts of this product may deteriorate and it may shorten
the lifetime of this product when using in locations subject
to high temperatures and high humidity.
Do not expose this product to direct heat sources such
as a heater.
Handle this product with care.
Do not drop this product, nor apply shock or vibration
to this product.
Failure to observe this may cause trouble.
Do not touch the dome cover with your bare hands.
The rain wash coating is applied to the surface of the dome
cover. Do not directly touch the surface of the dome cover
or wipe it with a cloth or other product. Failure to observe
this may reduce the effectiveness of the rain wash coating.
Cleaning this product body
Be sure to turn off the power before cleaning.
• When cleaning the dome cover, wash away any dirt or
other unwanted substances by pouring or spraying clean
water from a hose or spray bottle. Do not wipe the dome
cover with a cloth or other product. Do not use benzine,
thinner, alcohol, or any other types of solvents or detergents.
• When cleaning areas other than the dome cover, do not
use benzine, thinner, or any other types of solvents.
Failure to observe this may cause discoloration. When
using a chemical cloth for cleaning, read the caution
provided with the chemical cloth product.
Important:
• The camera position may be moved inadvertently
while cleaning the camera body. Restart the
product or refresh the camera position (position
refresh) to correct the camera position. Refer to the
Operating Instructions (included in the CD-ROM)
for further information.
What to do if "WARMING UP, PLEASE WAIT."
appears on the display.
This message indicates that the temperature inside the
camera has become extremely low.
In such a case, wait until the heater unit of the camera raises
the internal temperature (for around 2 hours or more in low
temperatures below -10 ºC {14 ºF}), and turn on the power again.
What to do if "CAMERA TEMP. TOO COLD. POWER
ON AT -30 DEG C (-22 DEG F) OR MORE." appears
on the display.
The ambient temperature is too cold.
Please turn on the power under the conditions where
the ambient temperature is above -30 °C {-22 °F}.
Discoloration on the CCD color filter
When continuously shooting a bright light source
such as a spotlight, the color filter of the CCD may
