2-4
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM (C) MCI Co. CCTV PRODUCT:CF224 EEPROM:0
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
MENU
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
Page (1/1)
✽ ✽ ✽ ✽ ✽
NTSC
1. FSC ADJUSTMENT
3. ALC LEVEL
4. AGC OFF GAIN
5.1. OB LEVEL
5.2. VIDEO OUT GAIN
5.3. OB CONFIRM
6. BURST LEVEL
7.1. 3200K R GAIN
7.2. 3200K B GAIN
7.3. 3200K PHASE
7.5. COLOR CENTER POINT ADJUSTMENT
8.1. ATW CONFIRM
8.2. HI LIGHT CHROMA CLIP
<CONTENTS> IC5 - 3 PIN [CCD] 28.63636 MHz + - 40Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD (F1) QUIT (F3) SAVE (F5)
Table 4-1
8
Press the SAVE (F5) key of the Computer, then the
Computer will ask you for the file name.
8
Type xxxxxxxx.EVR. Give an appropriate file name for
xxxxxxxx within 8 letters, but do not use CF224P.
8
Press the ENTER key.
8
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
8
Press the LOAD (F1) key and type CF224P.EVR and
press the ENTER key for presetting adjustment of the
Camera.
8
Press the ENTER key to start adjustment.
4.2. Adjustment Procedure-2
(E.V.R. Adjustment)
8
Insert new disk containing the E.V.R. Adjustment pro-
gram into IBM PC/AT and turn on the Power Switch of
IBM PC/AT.
8
When starting an adjustment, at the prompt, type
LADJ CF224P and press the ENTER key, an initial menu
will be displayed in Table 4-1.
4. Adjustment Procedure
8
Refer to the Wiring Diagram on page 3-1.
4.1. Adjustment Procedure-1
(1). Line Lock VCO Adjustment
Test Point:
TP1 (LL VCO)
Main Board
Adjust:
L301 (LL VCO)
Sensor Board
8
Set the Synchronization Mode Selector (on the SW Board
SW1) to LL position.
8
Connect the Digital Voltmeter to TP1.
8
Adjust L301 so that the voltage becomes 1.65 V ± 0.35 V.
8
Return the Synchronization Mode Selector (on the SW
Board) SW1 to INT position.
(2). Flange-back Adjustment
Test Point:
Video Output Connector
Adjust:
Flange-back Adjusting Cam
8
Referring to Fig. 4-1, loosen the Zoom Lock Screw at the
tip of the Zoom Lever.
8
Move the Zoom Lever to TELE side fully.
8
Loosen the Focus Lock Screw at the tip of the Focus
Lever.
8
Move the Focus Lever to FAR side fully.
8
Set the Radiation Chart.
8
Aim the Camera at the Radiation Chart 10m away.
8
Loosen the Flange-back Lock Screw that secures the
Flange-back Adjusting Cam.
8
Adjust the Flange-back Adjusting Cam to obtain best
focal point.
Focus Lever
(Focus Lock Screw)
Zoom Lever
(Zoom Lock Screw)
Flange-back
Adjusting Cam
Flange-back
Lock Screw
Fig. 4-1
8
Move the Zoom Lever to WIDE side fully.
8
Confirm that the focal point can be obtained by moving
the Focus Lever.
8
Tighten the Flange-back Lock Screw that secures the
Flange-back Adjusting Cam carefully.
8
Tighten the Zoom Lock Screw at the tip of the Zoom
Lever carefully.
8
Tighten the Focus Lock Screw at the tip of the Focus
Lever carefully.
NEAR
WIDE
FAR
TELE
