Panasonic Workio DP-C305 Скачать руководство пользователя | Manualshive

Страница: 597 / 920

background image

597

DP-C405/C305/C265

FEB 2008

Ver. 1.1

It will remain in this position until a different operation is performed (i.e. if the last operation was
2-Sided scanning, a Single-Sided scanning is performed).

2. Scanning the Front and the Back Side of an Original

The scanning of the Front and Back side of a 2-Sided original is accomplished by means of the
Selection Guide 1, and Selection Guide 2.
After the Front side of the original is scanned, the original is transported through the Selection Guide 1,
through the Selection Guide 2 that was rotated counter-clockwise by the Selection Solenoid, and is
carried beyond the Inverting Roller and upper Pinch Rollers into the Sub Tray. The original is carried for
a specified period of time after the trailing edge of the original triggers the Selection Sensor, and stops
within 10 to 20 mm from exiting the rollers. Then, the Selection Guide 2 is rotated clockwise by the
Pinch Roller Solenoid Assembly, and the reverse rotation of the ADF Motor 1 pulls the original back
around the Registration Roller 1, and proceeds to scan the Back side of the original.

3. Eject by Reverse Rotation

After the Back is scanned, the original is transported through the Selection Guide 1, through the
Selection Guide 2, and is carried beyond the Inverting Roller and lower Pinch Rollers, into the Sub
Tray, again stopping 10 to 20 mm from exiting the rollers.
The Selection Guide 2 is rotated clockwise by the Pinch Roller Solenoid Assembly, and the reverse
rotation of the ADF Motor 1 pulls the original back around the Registration Roller 1, however, this time
the original is routed to the Exit Roller, and exits into the ADF Base.

4. Sub Tray

The Inverting ADF system includes a Sub Tray, which supports the originals during the ejection mode
of the 2-Sided scanning operation.

Inverting Automatic Document Feeder (i-ADF)

8.3 in / 210 mm (A5)

8.5 in / 215.9 mm (INVOICE)

10.1 in / 257 mm (B5-R)

11.7 in / 297 mm (A4-R)

13 in / 330.2 mm (FLS1.2)

14.3 in / 364 mm (B4)

16.5 in / 420 mm (A3)

17 in / 431.8 mm (Ledger)

Sub Tray

Inverting Roller

Read Point

Paper Feed Roller

Pick Up Roller

Separation

Roller

Exit Roller

Transport Roller

Anti Drive Registration Roller

(Pinch Roller)

Anti Drive Exit Roller

(Pinch Roller)

Anti Drive Transport Roller (Pinch Roller)

Anti Drive Registration

Roller 2 (Pinch Roller)

Registration Roller 2

Registration Roller 1

Registration Sensor 3

Registration Sensor 2

Registration Sensor 1

Original Stopper

Original Detection Sensor

Original Guide

Original Tray

Selection Guide 2

Selection Sensor

Selection Guide 1

Exit Sensor

Inverting Guide Sheet

Anti Drive Exit Roller

(Pinch Roller)

«
...
595
596
597
598
599
...
»

Содержание Workio DP-C305

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Workio DP-C305

Бренд: HP Страницы: 80

Бренд: Sharp Страницы: 71

Бренд: Triumph Adler Страницы: 84

Бренд: Triumph Adler Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды