Panasonic Workio DP-C305 Скачать руководство пользователя

Страница: 469 / 920

469

DP-C405/C305/C265

FEB 2008

Ver. 1.1

Note:

These error codes will appear only when the optional accessories are installed. Refer to the appropriate
Optional Unit Service Manual.

E7-59 Finisher

Upper Limit
Sensor

Paper Height
detection Sensor
detects the Upper
Limit.

Finisher

1. Check the Stack Tray Paper Height

Detection Sensor, or Paper Hold Lever
Detection Sensor connectors.

2. Stack Tray Paper Height Detection

Sensor, or the Paper Hold Lever
Detection Sensor is defective.

3. Upper Limit Detection Sensor is

defective.

4. Check the Upper Limit Detection

Sensor connector.

5. PCB is defective. (Finisher Controller

PCB for

DA-FS405

/FS356/FS325 /

CONT PCB for

DA-FS402

/FS350/

FS320)

DA-
FS405/
FS402

FS356/
FS325/
FS350/
FS320

E7-60 Finisher

Aligning:
Rear Motor

Rear Aligning Home
Position Sensor
does not detect On/
Off.

Finisher

1. Rear Aligning Home Position Sensor is

defective.

2. Rear Aligning Motor is defective.

DA-
FS405

FS356/
FS325
only

E7-61 Finisher

Aligning:
Front Motor

Front Aligning
Home Position
Sensor does not
detect On/Off.

Finisher

1. Front Aligning Home Position Sensor is

defective.

2. Front Aligning Motor is defective.

DA-
FS405/
FS402

FS356/
FS325/
FS350/
FS320

E7-62 Finisher

Aligning:
Stapler

Stapler Sensor
detects Stapler Jam
twice continuously.

Finisher

1. Staple Jammed in the Cartridge.
2. Stapler Sensor is defective.
3. Stapler Motor is defective.

E7-63 Finisher

Backup RAM
1 (Punch)
Data Error

Backup RAM 1 Data
on Punch PCB is
abnormal.

Finisher

1. Punch PCB is defective.

DA-
FS405

FS356/
FS-325
only

E7-64 Finisher

Backup RAM
2 (Finisher)
Data Error

Backup RAM 2 Data
on Finisher
Controller PCB is
abnormal.

Finisher

1. Finisher Controller PCB is defective.

E7-65 Finisher

Communicati
on Error (EC
PCB-Finisher
PCB)

Communication
Error between EC
PCB and Finisher
PCB.

Finisher

1. Incorrect Finisher ROM Version.
2. Incorrect EC Firmware Version.

DA-
FS405/
FS402

FS356/
FS325/
FS350/
FS320

E7-90 Hardware

Key
Abnormal

Hardware Key is
incorrect.

Hardware

Key

1. Incorrect Hardware Key is installed.
2. Hardware Key is defective.

E7-91 Data Security

Kit Abnormal
(DP-C405 /
C354 Series)

Hardware Key (Data
Security Kit) is not
installed.

Hardware

Key

Hardware Key for Data Security Kit is not
installed.

E7: Optional Unit Error Codes

Code

Function

Contents

Section

Check Points

Unit

Содержание Workio DP-C305

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Workio DP-C305

Отзывы:

Похожие инструкции для Workio DP-C305

Бренды по названию

Популярные бренды

Panasonic Workio DP-C305, Руководство по обслуживанию

Результаты поиска

Содержание Workio DP-C305

Отзывы:

Похожие инструкции для Workio DP-C305

Бренды по названию

Популярные бренды