33
Install external filter (30 mesh or more, field supply)
before water inlet of indoor unit (with “WATER IN”
indication).
Refer to Diagram 4.1 for pipe connection of Panel
Heater, Floor Heater, Tank Unit, Solar Pump
Station, 3-way Valve Kit and etc. Fail to connect the
pipes appropriately might cause the unit malfunction.
Be sure to use two spanners to tighten the
connection. Further tighten the nuts with torque
wrench in specified torque as stated in the table.
If non-brass metallic piping is used for installation,
make sure to insulate the pipes to prevent galvanic
corrosion.
Make sure to insulate the water circuit pipes to
prevent reduction of heating capacity.
After installation, check the water leakage condition
in connection area during test run.
Nut size (Torque)
Model
Water
(SHF09D3E5/UH09DE5,
SHF12D6E5/UH12DE5)
Rp 1 1/4” [117.6 N•m]
CAUTION
Do not over tighten, over tightening cause gas leakage.
11.3.3.3 Indoor Unit Refrigerant Pipe
Installation
1 Please make flare after inserting flare nut
(located at joint portion of tube assembly) onto
the copper pipe. (In case of using long piping)
2 Do not use pipe wrench to open refrigerant
piping. Flare nut may be broken and cause
leakage. Use proper spanner or ring wrench.
3 Connect the piping:
o
Align the center of piping and sufficiently
tighten the flare nut with fingers.
o
Further tighten the flare nut with torque
wrench in specified torque as stated in the
table.
Piping size (Torque)
Model
Gas Liquid
SHF09D3E5/UH09DE5,
SHF12D6E5/UH12DE5
ø15.88mm (5/8”)
[65 N•m]
ø 9.52mm (3/8”)
[42 N•m]
CAUTION
Do not over tighten, over tightening cause gas leakage.
11.3.3.4 Drain Hose Installation
Use inner diameter 15 mm drain hose in the market.
This hose must to be installed in a continuously
downward direction and in a frost-free environment.
Do not insert this hose into sewage hose or
cleaning hose that may generate ammonia gas,
sulfuric gas, etc.
If necessary, use hose clamp to further tighten the
hose at drain hose connector to prevent leakage.
The water may drip from drain hose. Therefore
must ensure the outlet of the hose is always not
closed or blocked.
Содержание WH-SHF09D3E5
